Problem & Lösung

Praktische Antworten auf häufige Herausforderungen mit Kunststoffmaterialien

Artikel durchsuchen →

Q

PBT Dark Weld Line

A

PBT dark weld line treatment gives priority to temperature and speed; position transfer and overflow wells are mold-side countermeasures; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PBT; dark weld line; weld line; gate; overflow well

Q

PBT Draft Angle and Forced Demolding

A

PBT demolding design is differentiated according to whether it is filled or not; the forced demolding capability of pure material no longer exists in glass fiber grades; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PBT; draft angle; forced demolding; elongation; glass fiber

Q

PBT Vent Slot 0.02mm

A

PBT venting is precision work at the 0.02mm level; the window between gas trapping and overflow is guaranteed by mold precision; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PBT; vent slot; 0.02mm; overflow; burning

Q

PBT Hot Runner Forbidden Zone

A

The hot runner is a process forbidden zone for PBT; the two major risks of low-viscosity drooling and manifold degradation are superimposed; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PBT; hot runner; forbidden zone; degradation; drooling

Q

PBT Mold Deposit from Small Molecules

A

PBT mold deposit is a direct reflection of small-molecule content; making additives high-molecular and thermal stabilization reduce it from the source; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PBT; mold deposit; small molecules; oligomer; mold cleaning

Q

PBT Notch Sensitivity

A

Notch sensitivity is a shortcoming determined by PBT's molecular structure; fillet design is a mandatory requirement, and toughening modification is the performance way out; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PBT; notch sensitivity; fillet; stress concentration; toughening

Q

PBT mold temperature 50-75℃

A

PBT's fast crystallization determines the short cycle advantage; the 50-75℃ mold temperature range is the balance between crystallization quality and deformation control; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PBT; mold temperature; 50-75℃; crystallization; bending

Q

PBT flowability sudden change above melting point

A

PBT's melting point sudden change is its process characteristic; the sharp increase in flowability is both an advantage for thin-wall filling and a risk of flash and drooling; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PBT; melting point; flowability sudden change; flash; drooling

Q

PBT reinforced material equipment wear

A

Reinforced material wear is a continuous cost; wear-resistant configuration plus monitoring.; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar p...

Molds & Tooling PBT; wear; glass fiber; screw; mold; monitoring

Q

PBT venting design

A

Venting is a mandatory item in PBT mold design.; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar problems in the future

Molds & Tooling PBT; venting; air trap; end; maintenance; speed

Zurück 1 ... 86 87 88 89 90 91 92 ... 151 Weiter

Kategorien

Alle Themen 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382