문제 및 해결책

Q

Bubbles/voids on the surface of homopolymer polypropylene injection products

A

Bubbles and voids are mainly caused by moisture vaporization, gas entrainment, or insufficient shrinkage compensation; they need to be systematically solved from raw '2079851475616104451, injection process, and holding pressure parameters.

Material Drying bubblesvoidsraw '2079851475616104451holding pressuremulti-stage injection

Q

Silver streaks/material bloom on the surface of homopolymer polypropylene injection products

A

Silver streaks are mainly caused by raw material moisture, thermal degradation, or poor venting; systematic investigation is needed from three aspects: raw '2079851475616104451, temperature control, and mold venting.

Material Drying silver streakmaterial bloomraw '2079851475616104451thermal degradationmold venting

Q

Bubbles/voids on the surface of homopolymer polypropylene injection products (Variant: strengthened measures)

A

Bubbles and voids are mainly caused by moisture vaporization, gas entrainment, or insufficient shrinkage compensation; they need to be systematically solved from raw '2079851475616104451, injection process, and holding pressure parameters. Targeted preventive measures need to be taken in differen...

Material Drying bubblesvoidsraw '2079851475616104451holding pressuremulti-stage injection

Q

Silver streaks/material bloom on the surface of homopolymer polypropylene injection products (Variant: strengthened measures)

A

Silver streaks are mainly caused by raw material moisture, thermal degradation, or poor venting; systematic investigation is needed from three aspects: raw '2079851475616104451, temperature control, and mold venting. Targeted preventive measures need to be taken in different production scenarios.

Material Drying silver streakmaterial bloomraw '2079851475616104451thermal degradationmold venting

Q

Defects Caused by Insufficient Drying Before Processing of Block Copolymer Polypropylene Block Copolymer Polypropylene

A

Insufficient drying is a common root cause of processing defects, and a complete drying system and moisture content detection system need to be established.

Material Drying raw '2079851475616104451moisture contentsilver streakbubblesdehumidifying drying

Q

Bubbles/Pores on the Surface of Block Copolymer Polypropylene Extruded Products

A

Bubbles are caused by water vaporization or gas entrainment, and need to be solved from raw '2079851475616104451 and the venting system.

Material Drying bubblesporesraw '2079851475616104451ventingvolatiles

Q

Product Defects Caused by Excessive Moisture Content of Block Copolymer Polypropylene Raw Material

A

Excessive moisture content of the raw material is solved by sufficient drying, and a complete drying and storage management system needs to be established.

Material Drying moisture contentdryingsilver streakbubblesmoisture-proof storage

Q

Insufficient Impact Strength of Block Copolymer Polypropylene Injection Molded Products

A

Insufficient impact strength is usually caused by excessive internal stress or material degradation, and needs to be addressed from temperature parameters, drying, and regrind control.

Material Drying impact strengthinternal stressmolecular orientationmaterial degradationregrind control

Q

Silver Streaks/Material Flowers Appearing on the Surface of Block Copolymer Polypropylene Injection Molded Products

A

Silver streaks are mainly caused by raw material moisture, thermal degradation, or poor venting, and need to be systematically investigated from three aspects: raw '2079851475616104451, temperature control, and mold venting.

Material Drying silver streakmaterial flowerraw '2079851475616104451thermal degradationmold venting

Q

Bubbles/Voids Appearing on the Surface of Block Copolymer Polypropylene Injection-Molded Products (Variant: Strengthened Measures)

A

Bubbles and voids are mainly caused by moisture vaporization, gas involvement, or insufficient shrinkage compensation, and need to be systematically solved from raw '2079851475616104451, injection process, and holding parameters. Targeted preventive measures need to be taken in different producti...

Material Drying bubblevoidraw '2079851475616104451holding pressuremulti-stage injection

문제 및 해결책

카테고리

견적 받기