문제 및 해결책

일반적인 플라스틱 재료 문제에 대한 실질적인 답변

기사 둘러보기 →

Q

PEEK Fiber Floating and Appearance

A

Floating fibers rely on temperature and injection speed to promote encapsulation; mold condition also affects fiber distribution; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubles...

Injection Molding floating fiberfiber reinforcementappearancewetting

Q

PEEK Injection Pressure and Back Pressure Window

A

PEEK requires high injection pressure and low back pressure — for shear discoloration, check back pressure and screw speed first; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a tro...

Injection Molding injection pressure back pressure screw speed shear

Q

Mold Steel Selection Mistake for PEEK

A

H13 is the bottom line of PEEK mold steel — the money saved on a soft mold will be repaid double in accuracy; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Injection Molding mold steel H13 S136 high-temperature mold

Q

The Limits of Processing PEEK on Ordinary Machines

A

For PEEK processing, first ask whether the machine can reach 400℃ — barely running at full load is a prelude to failure; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Injection Molding machine capability high-temperature machine equipment selection temperature upper limit

Q

Process Parameter Transfer Failure of PEEK

A

The essence of PEEK process transfer is equivalent reproduction of the melt state, not copying parameters; the cavity pressure curve is the best reference for cross-equipment transfer; every piece of equipment needs independent verification.

Injection Molding PEEK；process transfer；equipment difference；calibration；cavity pressure；verification

Q

Insufficient '2079851475616104452 Machine Selection for PEEK

A

PEEK's hard requirements for equipment cannot be compensated by process techniques; equipment selection mistakes are congenital defects; investing in high-temperature dedicated equipment is a prerequisite for PEEK projects.

Injection Molding PEEK；'2079851475616104452 machine；selection；high temperature；temperature control；screw

Q

PEEK Flash

A

PEEK's high injection pressure places higher demands on clamping and mold rigidity; recurring flash mostly stems from mold wear rather than parameters; the mold maintenance cycle for high-temperature working conditions should be shortened.

Injection Molding PEEK；flash；clamping force；parting line；wear；high pressure

Q

Floating Fibers on Glass Fiber Reinforced PEEK

A

PEEK glass fiber floating is the combined result of fluidity and temperature management; high temperature and high speed are the most effective process means; the fiber orientation direction should be planned at the mold design stage for appearance parts.

Injection Molding PEEK；floating fiber；glass fiber；appearance；orientation；reinforcement

Q

Low Weld Line Strength of PEEK

A

PEEK weld lines cannot be completely eliminated — they can only be relocated and strengthened; high-temperature meeting is the first guarantee of interface strength; overflow wells are a worthwhile scrap cost for load-bearing parts.

Injection Molding PEEK；weld line；strength；meeting；overflow well；gate

Q

Short Shot of PEEK

A

PEEK short shot treatment follows the path of temperature first, then pressure, then structure; gate size is a hard constraint for glass fiber reinforced PEEK; high-speed filling must be implemented together with good venting.

Injection Molding PEEK；short shot；short shot；viscosity；gate；filling

이전 1 ... 118 119 120 121 122 123 124 ... 151 다음

카테고리

전체 주제 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382