문제 및 해결책

일반적인 플라스틱 재료 문제에 대한 실질적인 답변

기사 둘러보기 →

Q

Overall lack of gloss on PP products

A

PP gloss = the three elements of 'replication + mold + grade': mold temperature and holding pressure determine replication, polishing determines the upper limit, and the grade determines the ceiling; before making high gloss, first confirm whether the grade can be glossy, then talk about the proc...

Molds & Tooling PP; gloss; surface replication; polishing; mold temperature; grade

Q

Cavity-to-cavity inconsistency in PP multi-cavity molds

A

For multi-cavity molds, do a 'filling balance test' first before talking about the process window: when the runners are unbalanced, any process adjustment is just robbing Peter to pay Paul; cavity-to-cavity consistency must be guaranteed by the hardware balance of runners and cooling.

Molds & Tooling PP; multi-cavity; runner balance; uneven filling; cooling

Q

Whitening of PP weld lines

A

PP weld line whitening = 'cold front + enrichment of gas and impurities': the three axes of raising temperature, venting, and setting overflow wells will obviously reduce the white line; plan the gate in advance for appearance parts to hide the weld line.

Molds & Tooling PP; weld line; whitening; venting; overflow well

Q

Corrugation/roughness on the inner wall of PP-R pipes

A

PP-R inner wall problems mostly originate from die head distribution and pressure stability, not simply temperature; inner wall forming quality reflects the 'state' of the melt before entering sizing, so investigate from both the die head and pressure fluctuations.

Molds & Tooling PP-R; pipe; inner wall corrugation; die head; sizing; pressure

Q

Warpage of glass fiber reinforced PP

A

The orientation-type warpage of GF-PP is a 'gate-determined material problem'; the main attack direction is gate design and orientation analysis, not cooling; treating warpage as a problem solvable by temperature adjustment often leads to the trap of repeated mold trials.

Molds & Tooling PP; glass fiber; warpage; fiber orientation; gate; Moldflow

Q

Uneven surface gloss of PP products

A

PP gloss consistency = consistency of pressure and temperature distribution: first make the mold temperature uniform and transmit the pressure in place, then talk about polishing; batch-to-batch gloss drift mostly requires going back to check the regrind and color masterbatch, rather than repeate...

Molds & Tooling PP; uneven gloss; surface replication; mold temperature; holding pressure; color masterbatch

Q

Sticking of PP products to the mold (difficult demolding)

A

For PP mold sticking, first 'reduce pressure and temperature' to lessen gripping, then 'fix draft and polish' to reduce resistance, and finally deal with deep-cavity vacuum suction; the polishing quality of the mold along the demolding direction often affects the feel of 'easy or hard to demold' ...

Molds & Tooling PP; mold sticking; gripping force; draft angle; polishing; vacuum suction

Q

Insufficient weld line strength of PP

A

PP weld lines are difficult to eliminate completely; the correct approach is the three-pronged 'relocate the position + increase the convergence temperature + improve venting', and to avoid it in advance as a structural design issue rather than forcing adjustments on the machine afterward.

Molds & Tooling PP; weld line; knit line; venting; gate position; crystallization

Q

Post-shrinkage and dimensional drift of PP products

A

The core of PP dimension management is 'the post-aging dimension prevails': first unify the measurement time point, then use mold temperature and cooling to 'lock' crystallization in the mold as much as possible, and finally correct the mold with measured shrinkage; otherwise you will forever be ...

Molds & Tooling PP; post-shrinkage; post-crystallization; dimensional drift; aging; annealing

Q

PP Nozzle Drooling

A

PP's low viscosity makes drooling easy—'lower nozzle temperature + add suck-back' is the first-choice combination; if ineffective, replace the nozzle or use a valve gate; cold slug marks from drooling spread to the next shot—stop it at the source.

Molds & Tooling PP;drooling;nozzle;suck-back;valve gate

이전 1 ... 54 55 56 57 58 59 60 ... 151 다음

카테고리

전체 주제 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382