문제 및 해결책

일반적인 플라스틱 재료 문제에 대한 실질적인 답변

기사 둘러보기 →

Local Overheating Caused by Coking of Heat Transfer Oil Inside the Roll

This problem is a typical manifestation of local overheating caused by coking of heat transfer oil inside the roll in calendering. The core of the solution lies in the precise adjustment of nip compensation, uniform control of roll temperature distribution, and stability assurance of the feed sys...

Extrusion & Post local overheating caused by coking of heat transfer oil inside the roll

High-temperature Creep of Roll Surface Material

This problem is a typical manifestation of high-temperature creep of roll surface material in calendering. The core of the solution lies in the precise adjustment of nip compensation, uniform control of roll temperature distribution, and stability assurance of the feed system. It is recommended t...

Extrusion & Post roll surface wearhard impuritiesnatural wearroll surface protectionmetal detection

Excessive or Insufficient Deflection Compensation of Calender Rolls

This problem is a typical manifestation of excessive or insufficient deflection compensation of calender rolls in calendering. The core of the solution lies in the precise adjustment of nip compensation, uniform control of roll temperature distribution, and stability assurance of the feed system....

Extrusion & Post uneven roll temperatureheat transfer oil channelsroll end heat dissipationinfrared temperature measurementtemperature control deviation

Die Mandrel Offset in Extrusion of Thin-walled Pipes (<0.5mm)

This problem is a typical manifestation of die mandrel offset in extrusion of thin-walled pipes (<0.5mm) in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, speed, pressure) and precisi...

Extrusion & Post die mandrel offset in extrusion of thin-walled pipes (<0.5mm)pressure

Plasticizer Film Precipitated on the Inner Wall of the Sizing Sleeve

This problem is a typical manifestation of plasticizer film precipitated on the inner wall of the sizing sleeve in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, speed, pressure) and ...

Extrusion & Post coating exudation and powderingformulation compatibilitysufficient curingUV stabilizerweather resistance

Synchronization Loss of Corrugated Pipe Forming Modules

This problem is a typical manifestation of synchronization loss of corrugated pipe forming modules in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, speed, pressure) and precision cor...

Extrusion & Post synchronization loss of corrugated pipe forming modules

Die Electrocorrosion of High-temperature-resistant Engineering Plastics (Such as PEEK)

This problem is a typical manifestation of die electrocorrosion of high-temperature-resistant engineering plastics (such as PEEK) in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, spe...

Extrusion & Post die electrocorrosion of high-temperature-resistant engineering plastics (such as PEEK)

Pipe Extrusion at Extremely Low Temperatures (Workshop Below -10°C)

This problem is a typical manifestation of pipe extrusion at extremely low temperatures (workshop below -10°C) in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, speed, pressure) and p...

Extrusion & Post vacuum sizingpipe ovalityvacuum degreesizing sleeve designcooling water temperature

Black Specks Caused by Thermal Label Paper Scraps in Recycled Material

This problem is a typical manifestation of black specks caused by thermal label paper scraps in recycled material in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, speed, pressure) an...

Extrusion & Post black specks caused by thermal label paper scraps in recycled material

High-frequency Oscillation of Pipes in the Sizing Sleeve

This problem is a typical manifestation of high-frequency oscillation of pipes in the sizing sleeve in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, speed, pressure) and precision co...

Extrusion & Post high-frequency oscillation of pipes in the sizing sleeve

이전 1 ... 197 198 199 200 201 202 203 ... 224 다음

카테고리

전체 주제 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382

문제 및 해결책

카테고리

견적 받기