Sorun ve Çözüm

Yaygın plastik malzeme zorluklarına pratik yanıtlar

Makalelere Göz At →

Defects caused by insufficient drying of polyolefin plastomer polyolefin plastomer before processing

Insufficient drying is a common root cause of processing defects, and a complete drying system and moisture content testing system need to be established.

Material Drying raw '2079851475616104451moisture contentsilver streaksbubblesdehumidifying drying

2 görüntüleme

Tam Yanıtı Oku →

Bubbles/pores on the surface of polyolefin plastomer extruded products

Bubbles are caused by moisture vaporization or gas entrainment, and need to be solved from raw '2079851475616104451 and the venting system.

Material Drying bubblesporesraw '2079851475616104451ventingvolatiles

2 görüntüleme

Tam Yanıtı Oku →

Rough inner and outer walls of polyolefin plastomer pipes (Variant: Enhanced Measures)

Rough pipe walls are caused by low mold temperature or poor surface condition, and need to be solved from temperature control and mold maintenance. Targeted preventive measures need to be taken in different production scenarios.

Material Drying rough pipe walldie temperaturemandrel temperaturemold polishingsizing sleeve

2 görüntüleme

Tam Yanıtı Oku →

Improper production environment control in polyolefin plastomer polyolefin plastomer processing (Variant: strengthened measures)

The production environment is an important factor affecting processing quality, and a complete environmental control system needs to be established. Targeted preventive measures need to be taken in different production scenarios.

Material Drying environmental controlworkshop temperaturehumiditycooling water temperatureprocess stability

2 görüntüleme

Tam Yanıtı Oku →

Defects caused by insufficient drying before polyolefin plastomer polyolefin plastomer processing (Variant: strengthened measures)

Insufficient drying is a common root cause of processing defects, and a complete drying system and moisture content detection system needs to be established. Targeted preventive measures need to be taken in different production scenarios.

Material Drying raw '2079851475616104451moisture contentsilver streakbubbledehumidifying drying

2 görüntüleme

Tam Yanıtı Oku →

Bubbles/pores on the surface of polyolefin plastomer extruded products (Variant: strengthened measures)

Bubbles are caused by water vaporization or gas entrainment, and need to be solved from raw '2079851475616104451 and the venting system. Targeted preventive measures need to be taken in different production scenarios.

Material Drying bubbleporeraw '2079851475616104451ventingvolatiles

2 görüntüleme

Tam Yanıtı Oku →

Rough inner and outer walls of heat-resistant polyethylene pipes

Pipe wall roughness is caused by low mold temperature or poor surface condition, and needs to be solved from temperature control and mold maintenance.

Material Drying pipe wall roughnessdie temperaturemandrel temperaturemold polishingsizing sleeve

2 görüntüleme

Tam Yanıtı Oku →

Improper production environment control in heat-resistant polyethylene heat-resistant polyethylene processing

The production environment is an important factor affecting processing quality, and a complete environmental control system needs to be established.

Material Drying environmental controlworkshop temperaturehumiditycooling water temperatureprocess stability

2 görüntüleme

Tam Yanıtı Oku →

Defects caused by insufficient drying before heat-resistant polyethylene heat-resistant polyethylene processing

Insufficient drying is a common root cause of processing defects, and a complete drying system and moisture content detection system needs to be established.

Material Drying raw '2079851475616104451moisture contentsilver streakbubbledehumidifying drying

2 görüntüleme

Tam Yanıtı Oku →

Bubbles/pores on the surface of heat-resistant polyethylene extruded products

Bubbles are caused by water vaporization or gas entrainment, and need to be solved from raw '2079851475616104451 and the venting system.

Material Drying bubbleporeraw '2079851475616104451ventingvolatiles

2 görüntüleme

Tam Yanıtı Oku →

Önceki 1 ... 16 17 18 19 20 21 22 ... 144 Sonraki

Kategoriler

Tüm Konular 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382

Sorun ve Çözüm

Kategoriler

Teklif Al