Sorun ve Çözüm

Yaygın plastik malzeme zorluklarına pratik yanıtlar

Makalelere Göz At →

Large Creep Deformation of Block Copolymer Polypropylene Injection Molded Products

Creep deformation is an inherent characteristic of crystalline materials under long-term load, and needs to be controlled by increasing crystallinity, reducing stress, and selecting suitable materials.

Injection Molding creep deformationcrystallinityuse temperaturemolecular weightstress level

9 görüntüleme

Tam Yanıtı Oku →

Low Hardness of Block Copolymer Polypropylene Injection Molded Products

Low hardness is mainly caused by insufficient crystallinity or material degradation, and needs to be improved by increasing the mold temperature and holding pressure.

Injection Molding low hardnesscrystallinitymold temperatureholding pressurenucleating agent

9 görüntüleme

Tam Yanıtı Oku →

Severe Screw Wear of Block Copolymer Polypropylene '2079851475616104452 Machine

Screw wear is caused by materials, fillers, and operating parameters, and wear-resistant materials need to be selected and operating parameters reasonably controlled.

Injection Molding screw wearwear-resistant materialscrew rotation speedfiller wearscrew gap

9 görüntüleme

Tam Yanıtı Oku →

Unstable Cycle in Block Copolymer Polypropylene '2079851475616104452

Unstable cycle is caused by the accumulation of time fluctuations in each process, and the cooling, demolding, plasticizing, and equipment systems need to be investigated one by one.

Injection Molding unstable cyclecooling timeplasticizing timemold temperatureequipment maintenance

10 görüntüleme

Tam Yanıtı Oku →

Large Injection Pressure Fluctuation in Block Copolymer Polypropylene '2079851475616104452

Injection pressure fluctuation is caused by hydraulic system instability or plasticizing inconsistency, and the hydraulic, screw, and temperature control systems need to be systematically investigated.

Injection Molding pressure fluctuationhydraulic systemcheck ringtemperature stabilityplasticizing consistency

10 görüntüleme

Tam Yanıtı Oku →

Unstable Screw Retraction in Block Copolymer Polypropylene '2079851475616104452

Unstable screw retraction is caused by large plasticizing resistance or equipment wear, and the back pressure, temperature, and screw condition need to be optimized.

Injection Molding screw retractionback pressureplasticizingscrew wearuniform temperature

10 görüntüleme

Tam Yanıtı Oku →

Low Tensile Strength of Block Copolymer Polypropylene Injection Molded Products

Low tensile strength is mainly caused by material degradation or internal defects, and the processing temperature, shear, and regrind ratio need to be controlled.

Injection Molding tensile strengththermal degradationmolecular weightscrew rotation speedregrind ratio

9 görüntüleme

Tam Yanıtı Oku →

Burnt Marks/Burnt Spots Appearing on Block Copolymer Polypropylene Injection Molded Products

Burnt marks are the result of trapped gas in the cavity being compressed and heated, causing carbonization of the material; the core solution measures are to improve venting and reduce the injection speed.

Injection Molding burnt markburnt spotmold ventinginjection speedtrapped gas compression

10 görüntüleme

Tam Yanıtı Oku →

Out-of-Tolerance Coaxiality of Block Copolymer Polypropylene Injection Molded Products

Out-of-tolerance coaxiality is caused by core shift or asymmetric shrinkage, and needs to be solved from mold precision, gate symmetry, and temperature uniformity.

Injection Molding coaxialitycore shiftuneven wall thicknesssymmetrical gateuniform temperature

9 görüntüleme

Tam Yanıtı Oku →

Nozzle Blockage in Block Copolymer Polypropylene '2079851475616104452

Nozzle blockage is caused by cold material solidification or impurities, and needs to be solved from nozzle temperature, cold slug well design, and raw material cleanliness.

Injection Molding nozzle blockagenozzle temperaturecold materialimpuritiesalignment

9 görüntüleme

Tam Yanıtı Oku →

Önceki 1 ... 31 32 33 34 35 36 37 ... 151 Sonraki

Kategoriler

Tüm Konular 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382

Sorun ve Çözüm

Kategoriler

Teklif Al