Sorun ve Çözüm

Yaygın plastik malzeme zorluklarına pratik yanıtlar

Makalelere Göz At →

Resin accumulation

This problem is a typical manifestation of resin accumulation in compression molding; the core of the solution lies in proper preheating of the material and assurance of flowability, as well as precise matching of mold temperature and molding pressure. It is recommended to adjust coordinately fro...

Molds & Tooling fiber orientationglass fiber floatinggate sizemelt temperatureglass fiber content

3 görüntüleme

Tam Yanıtı Oku →

Fiber exposure

This problem is a typical manifestation of fiber exposure in compression molding; the core of the solution lies in proper preheating of the material and assurance of flowability, as well as precise matching of mold temperature and molding pressure. It is recommended to adjust coordinately from bo...

Molds & Tooling fiber orientationglass fiber floatinggate sizemelt temperatureglass fiber content

3 görüntüleme

Tam Yanıtı Oku →

Product surface reddening/discoloration

This problem is a typical manifestation of product surface reddening/discoloration in compression molding; the core of the solution lies in proper preheating of the material and assurance of flowability, as well as precise matching of mold temperature and molding pressure. It is recommended to ad...

Molds & Tooling curing degreecatalyst dosagemold temperaturecuring timepost-curing

2 görüntüleme

Tam Yanıtı Oku →

Cold material entering the mold too early

This problem is a typical manifestation of cold material entering the mold too early in compression molding; the core of the solution lies in proper preheating of the material and assurance of flowability, as well as precise matching of mold temperature and molding pressure. It is recommended to ...

Molds & Tooling cold slug marknozzle temperaturecold slug wellmold temperaturepoor gloss

3 görüntüleme

Tam Yanıtı Oku →

Improper mold closing speed

This problem is a typical manifestation of improper mold closing speed in compression molding; the core of the solution lies in proper preheating of the material and assurance of flowability, as well as precise matching of mold temperature and molding pressure. It is recommended to adjust coordin...

Molds & Tooling improper mold closing speedtemperature

3 görüntüleme

Tam Yanıtı Oku →

Vent groove blockage

This problem is a typical manifestation of vent groove blockage in compression molding; the core of the solution lies in proper preheating of the material and assurance of flowability, as well as precise matching of mold temperature and molding pressure. It is recommended to adjust coordinately f...

Molds & Tooling curing degreecatalyst dosagemold temperaturecuring timepost-curing

3 görüntüleme

Tam Yanıtı Oku →

Uneven mold temperature

This problem is a typical manifestation of uneven mold temperature in compression molding; the core of the solution lies in proper preheating of the material and assurance of flowability, as well as precise matching of mold temperature and molding pressure. It is recommended to adjust coordinatel...

Molds & Tooling uneven mold temperaturetemperaturemold

2 görüntüleme

Tam Yanıtı Oku →

Mold wear

This problem is a typical manifestation of mold wear in compression molding; the core of the solution lies in proper preheating of the material and assurance of flowability, as well as precise matching of mold temperature and molding pressure. It is recommended to adjust coordinately from both as...

Molds & Tooling dimensional accuracyholding pressuremold temperatureshrinkage ratecheck ring

2 görüntüleme

Tam Yanıtı Oku →

Poor sheet material (SMC/BMC) flowability

This problem is a typical manifestation of poor sheet material (SMC/BMC) flowability in compression molding; the core of the solution lies in proper preheating of the material and assurance of flowability, as well as precise matching of mold temperature and molding pressure. It is recommended to ...

Molds & Tooling sheet material (SMCtemperaturepressuremold

2 görüntüleme

Tam Yanıtı Oku →

Uneven thickness

This problem is a typical manifestation of uneven thickness in compression molding; the core of the solution lies in proper preheating of the material and assurance of flowability, as well as precise matching of mold temperature and molding pressure. It is recommended to adjust coordinately from ...

Molds & Tooling feeding amountmaterial flowabilityweighing accuracyhopper bridgingmaterial distribution

3 görüntüleme

Tam Yanıtı Oku →

Önceki 1 ... 141 142 143 144 145 146 147 ... 151 Sonraki

Kategoriler

Tüm Konular 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382

Sorun ve Çözüm

Kategoriler

Teklif Al