Sorun ve Çözüm

Yaygın plastik malzeme zorluklarına pratik yanıtlar

Makalelere Göz At →

Local Overheating Caused by Coking of Heat Transfer Oil Inside the Roll

This problem is a typical manifestation of local overheating caused by coking of heat transfer oil inside the roll in calendering. The core of the solution lies in the precise adjustment of nip compensation, uniform control of roll temperature distribution, and stability assurance of the feed sys...

Extrusion & Post local overheating caused by coking of heat transfer oil inside the roll

2 görüntüleme

Tam Yanıtı Oku →

High-temperature Creep of Roll Surface Material

This problem is a typical manifestation of high-temperature creep of roll surface material in calendering. The core of the solution lies in the precise adjustment of nip compensation, uniform control of roll temperature distribution, and stability assurance of the feed system. It is recommended t...

Extrusion & Post roll surface wearhard impuritiesnatural wearroll surface protectionmetal detection

2 görüntüleme

Tam Yanıtı Oku →

Excessive or Insufficient Deflection Compensation of Calender Rolls

This problem is a typical manifestation of excessive or insufficient deflection compensation of calender rolls in calendering. The core of the solution lies in the precise adjustment of nip compensation, uniform control of roll temperature distribution, and stability assurance of the feed system....

Extrusion & Post uneven roll temperatureheat transfer oil channelsroll end heat dissipationinfrared temperature measurementtemperature control deviation

2 görüntüleme

Tam Yanıtı Oku →

Die Mandrel Offset in Extrusion of Thin-walled Pipes (<0.5mm)

This problem is a typical manifestation of die mandrel offset in extrusion of thin-walled pipes (<0.5mm) in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, speed, pressure) and precisi...

Extrusion & Post die mandrel offset in extrusion of thin-walled pipes (<0.5mm)pressure

2 görüntüleme

Tam Yanıtı Oku →

Plasticizer Film Precipitated on the Inner Wall of the Sizing Sleeve

This problem is a typical manifestation of plasticizer film precipitated on the inner wall of the sizing sleeve in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, speed, pressure) and ...

Extrusion & Post coating exudation and powderingformulation compatibilitysufficient curingUV stabilizerweather resistance

2 görüntüleme

Tam Yanıtı Oku →

Synchronization Loss of Corrugated Pipe Forming Modules

This problem is a typical manifestation of synchronization loss of corrugated pipe forming modules in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, speed, pressure) and precision cor...

Extrusion & Post synchronization loss of corrugated pipe forming modules

2 görüntüleme

Tam Yanıtı Oku →

Die Electrocorrosion of High-temperature-resistant Engineering Plastics (Such as PEEK)

This problem is a typical manifestation of die electrocorrosion of high-temperature-resistant engineering plastics (such as PEEK) in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, spe...

Extrusion & Post die electrocorrosion of high-temperature-resistant engineering plastics (such as PEEK)

2 görüntüleme

Tam Yanıtı Oku →

Pipe Extrusion at Extremely Low Temperatures (Workshop Below -10°C)

This problem is a typical manifestation of pipe extrusion at extremely low temperatures (workshop below -10°C) in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, speed, pressure) and p...

Extrusion & Post vacuum sizingpipe ovalityvacuum degreesizing sleeve designcooling water temperature

2 görüntüleme

Tam Yanıtı Oku →

Black Specks Caused by Thermal Label Paper Scraps in Recycled Material

This problem is a typical manifestation of black specks caused by thermal label paper scraps in recycled material in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, speed, pressure) an...

Extrusion & Post black specks caused by thermal label paper scraps in recycled material

2 görüntüleme

Tam Yanıtı Oku →

High-frequency Oscillation of Pipes in the Sizing Sleeve

This problem is a typical manifestation of high-frequency oscillation of pipes in the sizing sleeve in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, speed, pressure) and precision co...

Extrusion & Post high-frequency oscillation of pipes in the sizing sleeve

2 görüntüleme

Tam Yanıtı Oku →

Önceki 1 ... 197 198 199 200 201 202 203 ... 224 Sonraki

Kategoriler

Tüm Konular 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382

Sorun ve Çözüm

Kategoriler

Teklif Al