Sorun ve Çözüm

Yaygın plastik malzeme zorluklarına pratik yanıtlar

Makalelere Göz At →

Uneven transverse stretching

This problem is a typical manifestation of uneven transverse stretching in calender molding. The core of the solution lies in precise adjustment of roll gap compensation, uniform control of roll temperature distribution, and assurance of feed system stability. It is recommended to start troublesh...

Extrusion & Post curing oventemperature sensorhot air circulationair speed distributionline speed matching

2 görüntüleme

Tam Yanıtı Oku →

Rough surface / lusterless

This problem is a typical manifestation of rough surface / lusterless in calender molding. The core of the solution lies in precise adjustment of roll gap compensation, uniform control of roll temperature distribution, and assurance of feed system stability. It is recommended to start troubleshoo...

Extrusion & Post coating glossmatting agent dispersioncuring degreesubstrate roughnessleveling time

2 görüntüleme

Tam Yanıtı Oku →

Fish eyes / gel particles

The essence of gel particles (fish eyes) is ultra-high molecular weight components or cross-linked gels in the resin that are not completely melted. The solution approach is "heat up + filter + change material": increase plastication temperature to ensure full melting, use screens to filter gel p...

Extrusion & Post gel particles fish eyeshigh molecular weight componentsplastication temperaturescreen filtrationresin purity

2 görüntüleme

Tam Yanıtı Oku →

Surface water marks / cold spots

This problem is a typical manifestation of surface water marks / cold spots in calender molding. The core of the solution lies in precise adjustment of roll gap compensation, uniform control of roll temperature distribution, and assurance of feed system stability. It is recommended to start troub...

Extrusion & Post surface water marksroll temperature too lowfeed temperaturebank renewalcalendering speed

2 görüntüleme

Tam Yanıtı Oku →

Uneven film thickness / transverse thickness variation

The essence of transverse thickness unevenness of calendered film is uneven distribution of roll gap along the axial direction. The core of the solution is "precise compensation": compensate roll deflection through precise adjustment of crown and cross angle, combined with real-time feedback fine...

Extrusion & Post transverse thickness variationcrown compensationcross angleroll gap uniformityonline thickness measurement

2 görüntüleme

Tam Yanıtı Oku →

Extruded pipe surface sink marks

This problem is a typical manifestation of extruded pipe surface sink marks in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, speed, pressure) and precision correction of the die/sizi...

Extrusion & Post pipe wall thicknessdie concentricitysizing sleeve centeringvacuum sizingonline thickness measurement

2 görüntüleme

Tam Yanıtı Oku →

Heater band overheating and burnout

This problem is a typical manifestation of heater band overheating and burnout in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, speed, pressure) and precision correction of the die/s...

Extrusion & Post heater band overheating and burnout

2 görüntüleme

Tam Yanıtı Oku →

Poor venting in feed section

This problem is a typical manifestation of poor venting in feed section in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, speed, pressure) and precision correction of the die/sizing s...

Extrusion & Post poor ventingvent port spewingvacuum pipelinescrew conveying matchingvent port design

2 görüntüleme

Tam Yanıtı Oku →

Extruder torque too high

This problem is a typical manifestation of extruder torque too high in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, speed, pressure) and precision correction of the die/sizing syste...

Extrusion & Post screen cloggingraw material cleanlinessfiltration mesh countgel particlesautomatic screen changer

2 görüntüleme

Tam Yanıtı Oku →

Insufficient pipe burst pressure

This problem is a typical manifestation of insufficient pipe burst pressure in extrusion molding. The core of the solution lies in eliminating the root cause of the defect through systematic optimization of process parameters (temperature, speed, pressure) and precision correction of the die/sizi...

Extrusion & Post internal stresscooling ratedraw ratioannealing treatmentmolecular orientation

2 görüntüleme

Tam Yanıtı Oku →

Önceki 1 ... 217 218 219 220 221 222 223 224 Sonraki

Kategoriler

Tüm Konular 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382

Sorun ve Çözüm

Kategoriler

Teklif Al