Sorun ve Çözüm

Yaygın plastik malzeme zorluklarına pratik yanıtlar

Makalelere Göz At →

Carbonized black specks appearing on the product surface

In summary, the causes of the "Carbonized black specks appearing on the product surface" problem can be attributed to the combined action of multiple factors such as Carbonized impurities in the sheet, Carbon deposits on the mold surface. Solving this problem requires starting from aspects such a...

Thermoforming Carbonized black specks appearing on the product surface '2079851475616104458 mold design surface quality

2 görüntüleme

Tam Yanıtı Oku →

Performance degradation of sheet made from recycled material

In summary, the causes of the "Performance degradation of sheet made from recycled material" problem can be attributed to the combined action of multiple factors such as Recycled material degradation, High recycled material ratio. Solving this problem requires starting from aspects such as Limit ...

Thermoforming Performance degradation of sheet made from recycled material '2079851475616104458 recycled material management thermal stability

2 görüntüleme

Tam Yanıtı Oku →

Thin walls of the product after deep drawing

In summary, the causes of the "Thin walls of the product after deep drawing" problem can be attributed to the combined action of multiple factors such as Stretch ratio too large, Pre-stretch plug not used. Solving this problem requires starting from aspects such as Use plug pre-stretching, Reduce...

Thermoforming Thin walls of the product after deep drawing '2079851475616104458 stretch ratio

2 görüntüleme

Tam Yanıtı Oku →

Insufficient sheet clamping force

In summary, the causes of the "Insufficient sheet clamping force" problem can be attributed to the combined action of multiple factors such as Insufficient clamping frame pressure, Clamping surface wear. Solving this problem requires starting from aspects such as Increase the clamping pressure, R...

Thermoforming Insufficient sheet clamping force '2079851475616104458 pressure adjustment

2 görüntüleme

Tam Yanıtı Oku →

Inconsistent products from multiple cavities

In summary, the causes of the "Inconsistent products from multiple cavities" problem can be attributed to the combined action of multiple factors such as Uneven heating, Different conditions among cavities. Solving this problem requires starting from aspects such as Optimize the heating uniformit...

Thermoforming Inconsistent products from multiple cavities '2079851475616104458 temperature control heating process

2 görüntüleme

Tam Yanıtı Oku →

Product springback deformation after demolding

In summary, the causes of the "Product springback deformation after demolding" problem can be attributed to the combined action of multiple factors such as Elastic recovery of the sheet, Insufficient cooling. Solving this problem requires starting from aspects such as Extend the cooling time, Red...

Thermoforming Product springback deformation after demolding '2079851475616104458 cooling process de'2079851475616104453 stress control

2 görüntüleme

Tam Yanıtı Oku →

Low sheet heating efficiency

In summary, the causes of the "Low sheet heating efficiency" problem can be attributed to the combined action of multiple factors such as Insufficient heater power, Heater aging. Solving this problem requires starting from aspects such as Replace with high-power heaters, Clean the reflector plate...

Thermoforming Low sheet heating efficiency '2079851475616104458 heating process

2 görüntüleme

Tam Yanıtı Oku →

Insufficient filling of product reinforcing ribs

In summary, the causes of the "Insufficient filling of product reinforcing ribs" problem can be attributed to the combined action of multiple factors such as Insufficient forming pressure or vacuum level, Poor venting at that location. Solving this problem requires starting from aspects such as I...

Thermoforming Insufficient filling of product reinforcing ribs '2079851475616104458 pressure adjustment venting design

2 görüntüleme

Tam Yanıtı Oku →

Uneven gloss on the product surface

In summary, the causes of the "Uneven gloss on the product surface" problem can be attributed to the combined action of multiple factors such as Uneven mold surface finish, Uneven sheet temperature. Solving this problem requires starting from aspects such as Uniformly polish the mold surface, Imp...

Thermoforming Uneven gloss on the product surface '2079851475616104458 temperature control mold design surface quality

2 görüntüleme

Tam Yanıtı Oku →

Tearing at the corners of the product

In summary, the causes of the "Tearing at the corners of the product" problem can be attributed to the combined action of multiple factors such as Corner radius too small, Uneven sheet temperature. Solving this problem requires starting from aspects such as Increase the corner radius, Optimize th...

Thermoforming Tearing at the corners of the product '2079851475616104458 temperature control stretch ratio

2 görüntüleme

Tam Yanıtı Oku →

Önceki 1 ... 8 9 10 11 12 13 14 15 Sonraki

Kategoriler

Tüm Konular 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382

Sorun ve Çözüm

Kategoriler

Teklif Al