المشاكل والحلول

إجابات عملية على التحديات الشائعة في مواد البلاستيك

تصفح المقالات →

Q

ASA silver streak insufficient drying

A

Drying investigation for ASA silver streak is primary; 80°C is the standard; verification and storage prevent recurrence.; After confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Material Drying ASA；silver streak；drying；80°C；moisture；performance

Q

ASA drying specification

A

ASA drying 80-85°C and 2-4 hours is the standard; equipment differences must be managed; verification ensures quality.; After confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Material Drying ASA；drying；80-85°C；2-4 hours；hopper；oven

Q

ASA winter production defects increase

A

ASA winter defects are the result of chain effects of environmental temperature; seasonal process adjustments should be standardized; environmental parameter records help abnormality tracing.; After confirming effectiveness, solidify the parameters and practices into the work instruction to preve...

Material Drying ASA；winter；environment；silver streak；preheating；seasonal

Q

ASA insufficient drying silver streak

A

90% of ASA silver streaks originate from insufficient drying; 3~5 hours drying is a supplier specification rather than a suggestion; if the moisture problem is not solved, any process adjustment is only treating the symptoms.

Material Drying ASA; silver streak; drying; moisture; embrittlement; 80℃

Q

AEPDS drying management

A

AEPDS drying management refers to ABS but needs adjustment; verification ensures quality; prevent both excess and insufficiency.; After confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Material Drying AEPDS; drying; silver streak; hygroscopicity; rubber phase; moisture content

Q

ABS weld line bubble

A

For ABS weld line bubbles check venting and drying; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar problems later

Material Drying weld line bubble venting convergence drying

Q

ABS dimensional deviation

A

ABS dimensions rely on parameter locking and SPC monitoring; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar problems later

Material Drying dimensional deviation shrinkage SPC parameters

Q

ABS bubble

A

ABS bubbles are divided into three types, distribution points to the cause; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar problems later

Material Drying bubble moisture degradation shrinkage void

Q

ABS silver streak misjudged as venting

A

For ABS silver streaks look at distribution first, overall random means moisture; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar problems later

Material Drying silver streak misjudgment moisture distribution

Q

ABS silver streak non-moisture causes

A

The non-moisture causes of ABS silver streaks are in-depth diagnosis; gate, temperature and homogenization are adjustment directions; distinction ensures precise treatment.; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Material Drying ABS; silver streak; non-moisture; melt temperature; shear rate; bubble

السابق 1 ... 121 122 123 124 125 126 127 ... 144 التالي

الفئات

جميع المواضيع 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382