المشاكل والحلول

إجابات عملية على التحديات الشائعة في مواد البلاستيك

تصفح المقالات →

Q

PA66 temperature resistance selection advantages

A

The watershed between PA6 and PA66 is temperature; choose 66 for high temperature, choose 6 to save cost at normal temperature, wrong selection cannot be remedied later; after confirming effectiveness, fix the parameters and practices into the work instructions to prevent recurrence

Material Analysis PA66；PA6；selection；heat resistance；engine compartment

Q

PA66 melt temperature 270-300℃

A

PA66 temperature window is only 20-30℃ above the melting point, the narrowest among the four major nylons; 300℃ is an absolute red line, measured calibration cannot be omitted; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Material Analysis PA66; melt temperature; 270-300℃; narrow window; degradation

Q

PA66 narrow processing temperature window

A

PA66='narrow window material': temperature control precision is the threshold; a 20~30℃ window means temperature control equipment and measured calibration must be in place; crude temperature adjustment does not work on PA66.

Material Analysis PA66; temperature window; melting point; thermal degradation; viscosity

Q

Treatment of PA12 SLS Unsintered Powder

A

70% unsintered powder is the bulk of the cost, and fluidity evaluation determines the reuse method; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a reference for troubleshooting sim...

Material Analysis unsintered powderfluiditychemical regenerationpowder spreading

Q

PA12 SLS Recycled Powder Aging Mechanism

A

Powder aging is molecular weight and crystallinity drift, and thermal performance monitoring determines retention or disposal; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a refere...

Material Analysis powder agingsecondary crystallizationporositymonitoring

Q

PA12 SLS Powder Recycling Ratio

A

Blending recycled powder with new powder at 1:2 is the economic-quality balance point, and use times must be traced; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a reference for tr...

Material Analysis SLS powder recyclingratiocosttraceability

Q

PA12 SLS Nitrogen Protection and Yellowing

A

For SLS yellowing, first check nitrogen purity; 99.9% is the bottom line for oxidation prevention; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a reference for troubleshooting simi...

Material Analysis SLS nitrogenyellowingoxidationatmosphere protection

Q

PA12 Melt Temperature Upper Limit Control

A

310℃/270℃ are the double red lines of PA12 temperature, and filling problems should not rely only on raising temperature; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Material Analysis temperature upper limitflame-retardant gradethermal degradationactual melt temperature measurement

Q

PA12 Melt Temperature Graded Setting

A

PA12 temperature is set in grades according to whether it is reinforced or not, and the temperature card must be changed when changing grades; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include this case in the defect arc...

Material Analysis melt temperaturereinforced gradetemperature gradingmaterial change

Q

MS Foaming Agent Application

A

Parameters and storage of MS foaming process are the key to quality; control ensures foaming effect; management prevents deterioration.; After confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Material Analysis MS;foaming agent;autoclave;temperature;storage;quality

السابق 1 ... 122 123 124 125 126 127 128 ... 135 التالي

الفئات

جميع المواضيع 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382