문제 및 해결책

일반적인 플라스틱 재료 문제에 대한 실질적인 답변

기사 둘러보기 →

Q

PEEK Compression Molding Particle Boundary Marks as Weak Lines

A

Pellet molding boundary marks are congenital weak lines; fine powder plus directional avoidance is the response; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference...

Processing Machinery compression moldingparticle boundary markfine powderstrength weak point

Q

PEEK Black Speck Contamination Troubleshooting

A

PEEK black specks are a whole-chain test; check raw material, equipment, and auxiliary machines in three lines in parallel; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshootin...

Processing Machinery black speckcontaminationcarbonizationcleaning

Q

PEEK Melt Viscosity Dual Sensitive Regions

A

380℃ is the watershed of PEEK machine adjustment logic: adjust temperature at low temperature and adjust speed at high temperature; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Processing Machinery melt viscositytemperature sensitivityshear sensitivitymachine adjustment

Q

Missing Shutdown Purging Procedure for PEEK

A

Shutting down with material in the barrel is a big taboo for PEEK — purging with HDPE is only complete when the droplets are clean; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Processing Machinery shutdown purging HDPE carbonization black speck

Q

Actual Measurement Calibration of PEEK Melt Temperature

A

PEEK process transfer is based on the actually measured melt temperature, and set values are for reference only; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting refe...

Processing Machinery actual melt temperature measurement air-shot temperature calibration machine difference

Q

Nozzle Temperature and Cold Slug of PEEK

A

Matching the nozzle temperature to the front zone is a hard requirement, and the cold slug well receives the front cold material; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a tro...

Processing Machinery nozzle temperature cold slug cold slug well short shot

Q

Shutdown Thermal Stability Management of PEEK

A

PEEK shutdowns are handled in 1-hour/3-hour graded levels, and the first shot after restart must be scrapped; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Processing Machinery shutdown thermal stability purging restart

Q

Particle Contamination of PEEK Semiconductor Parts

A

The competitive dimension of semiconductor PEEK parts is cleanliness control; tracing particle contamination must cover the entire chain from processing to packaging; ultrasonic cleaning is the standard post-treatment process.

Processing Machinery PEEK；semiconductor；particle contamination；cleanliness；cleaning；wafer

Q

Poor Color Powder Dispersion in High-Mixing PEEK

A

For PEEK coloring, the dedicated color masterbatch granule route is preferred; directly adding color powder to a narrow-window material is high risk; the balance point between dispersion and degradation needs to be determined by testing.

Processing Machinery PEEK；color powder；dispersion；color masterbatch granule；color difference；mixing

Q

Shutdown Carbonization Failure of PEEK

A

The core of PEEK shutdown management is dual control of time and temperature; 15 minutes is the empirical red line; the cost of discharging material at shutdown is far lower than batch scrap caused by degraded material mixing in.

Processing Machinery PEEK；shutdown；carbonization；degradation；cleaning；specification

이전 1 ... 118 119 120 121 122 123 124 ... 203 다음

카테고리

전체 주제 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382