문제 및 해결책

Q

Bubbles/Voids Appearing on the Surface of High-Density Polyethylene Injection-Molded Products

A

Bubbles and voids are mainly caused by moisture vaporization, gas involvement, or insufficient shrinkage compensation, and need to be systematically solved from raw '2079851475616104451, injection process, and holding parameters.

Material Drying bubblevoidraw '2079851475616104451holding pressuremulti-stage injection

Q

Warpage Deformation of High-Density Polyethylene Injection-Molded Products

A

Warpage deformation is the core difficulty in the '2079851475616104452 of crystalline materials; its essence is the internal stress caused by non-uniform shrinkage, and it needs to be systematically controlled from multiple dimensions of design, process, and mold.

Injection Molding warpage deformationcrystallization shrinkageuniform mold temperatureuniform wall thicknesscooling time

Q

Silver Streaks/Material Flow Marks on the Surface of High-Density Polyethylene Injection-Molded Products

A

Silver streaks are mainly caused by moisture in the raw material, thermal degradation, or poor venting, and need to be systematically investigated from three aspects: raw '2079851475616104451, temperature control, and mold venting.

Material Drying silver streakmaterial flow markraw '2079851475616104451thermal degradationmold venting

Q

Sink Marks at Thick-Wall Sections of High-Density Polyethylene Injection-Molded Products

A

Sink marks are a typical defect in the '2079851475616104452 of crystalline materials; the root cause is that local volume shrinkage is not effectively compensated, and it needs to be solved coordinately from three aspects: holding parameters, gate design, and cooling conditions.

Injection Molding sink markholding pressurecrystallization shrinkagegate designuniform wall thickness

Q

Weld Lines on High-Density Polyethylene Injection-Molded Products (Variant: Strengthened Measures)

A

Weld lines are a manifestation of poor melt convergence and fusion; the melt fusion quality is improved by increasing the melt temperature, injection speed, and mold temperature. Targeted preventive measures need to be taken in different production scenarios.

Injection Molding weld linemelt convergenceinjection speedmold temperaturegate design

Q

Silver Streaks/Material Flow Marks on the Surface of High-Density Polyethylene Injection-Molded Products (Variant: Strengthened Measures)

A

Silver streaks are mainly caused by moisture in the raw material, thermal degradation, or poor venting, and need to be systematically investigated from three aspects: raw '2079851475616104451, temperature control, and mold venting. Targeted preventive measures need to be taken in different produc...

Material Drying silver streakmaterial flow markraw '2079851475616104451thermal degradationmold venting

Q

Sink Marks at Thick-Wall Sections of High-Density Polyethylene Injection-Molded Products (Variant: Strengthened Measures)

A

Sink marks are a typical defect in the '2079851475616104452 of crystalline materials; the root cause is that local volume shrinkage is not effectively compensated, and it needs to be solved coordinately from three aspects: holding parameters, gate design, and cooling conditions. Targeted preventi...

Injection Molding sink markholding pressurecrystallization shrinkagegate designuniform wall thickness

Q

Color Difference/Unstable Color of Cast Polypropylene Film ABS Products

A

ABS color difference is caused by uneven pigment dispersion and process fluctuations.

Processing Machinery color differenceABScolor masterbatch dispersionprocessing temperaturemixing screw

Q

Batch Instability of Impact Strength of Cast Polypropylene Film Products

A

The stability of impact strength depends on the consistency of raw materials and the stability of the process.

Material Analysis impact strengthbatch instabilityraw material inspectiontemperature controltest standard

Q

Surface Static Electricity Problem of Cast Polypropylene Film Products

A

The static electricity problem is caused by the high insulation of the material.

Molding Process static electricityantistatic agentvolume resistanceambient humiditysurface treatment

문제 및 해결책

카테고리

견적 받기