문제 및 해결책

일반적인 플라스틱 재료 문제에 대한 실질적인 답변

기사 둘러보기 →

Q

Cautious Use of Hot Runners for PPS

A

PPS hot runners are usable but conditional; the valve-gate prohibition for glass fiber grades and temperature control accuracy are two disciplines; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PPS; hot runner; valve gate; wear resistance; temperature control

Q

PPS Equipment Wear Protection

A

Equipment protection for PPS glass fiber grades must be front-loaded; a bimetallic barrel plus Stellite flights is the long-life configuration; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Processing Machinery PPS; equipment wear; bimetallic; Stellite; screw

Q

PPS Mold Steel Selection

A

PPS mold material selection is a triple requirement of heat resistance, wear resistance, and corrosion resistance; HRC55-60 is the baseline for mass-production life; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PPS; mold steel; SKD-11; HRC55-60; abrasion

Q

PPS Nozzle Drooling

A

For PPS drooling treatment, nozzle structure takes priority; drying and temperature fine-tuning are supporting measures; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Material Drying PPS; nozzle; drooling; anti-drool nozzle; drying

Q

PPS Check Valve and Retention

A

The low viscosity of PPS amplifies the impact of check valve failure; behind metering stability lies valve health; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PPS; check valve; metering; cold material spot; nozzle

Q

PPS Cleaning Forbidden Zone

A

The forbidden zone for PPS cleaning is PVC and POM; this single misoperation can destroy the barrel, the screw, and the entire batch of products at the same time; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Processing Machinery PPS; cleaning; HDPE; PVC; POM

Q

PPS Black Specks from Residual Material

A

Ninety percent of PPS black specks trace back to shutdown retention; the 280°C heat-preservation line and HDPE replacement are standard procedures; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Processing Machinery PPS; black speck; retention; 280°C; HDPE cleaning

Q

PPS Burning and Gas

A

The PPS venting system must be designed for high-contamination conditions; groove depth precision plus frequent cleaning, and vacuum venting is the ultimate solution; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PPS; burnt; vent groove; 5-8/1000mm; vacuum venting

Q

PPS Insufficient Filling Troubleshooting

A

PPS short shot troubleshooting prioritizes temperature, with structure as the backstop; after the process reaches its limit, the gate and flow-length ratio are the fundamental solutions; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PPS; insufficient filling; short shot; flow-length ratio; gate

Q

PPS Weld Line Strength

A

The difficulty of PPS weld line treatment lies in the 0.0127mm venting precision; temperature and speed optimization combined with position transfer are used together; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PPS; weld line; vent groove; 0.0127mm; gate

이전 1 ... 670 671 672 673 674 675 676 ... 1164 다음

카테고리

전체 주제 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382