문제 및 해결책

일반적인 플라스틱 재료 문제에 대한 실질적인 답변

기사 둘러보기 →

Q

PPO Purging Material Selection

A

PPO purging uses PS and acrylic; alloy grades follow the base material procedures; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for subsequent similar problems

Molding Process purging materialPSacrylicmaterial change

Q

PPO Shutdown Temperature Graded Management

A

PPO shutdown is handled in grades of 15 min/2 h/12 h; proceduralization avoids arbitrary decisions; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Processing Machinery shutdown managementgraded coolingrestartprocedure

Q

PPO Melt Discoloration After 2 Hours Residence

A

PPO melt residence of 2 hours is the discoloration line; over time, clean the machine and scrap the first shots at restart; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Processing Machinery residence timediscolorationcleaninginterruption

Q

Boundary of PPO Hot Mold for Stress Reduction

A

PPO hot mold 110-150℃ reduces stress; above 150℃ the loss outweighs the gain; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling hot moldinternal stressbubblingcycle

Q

Bidirectional Influence of PPO Mold Temperature on Defects

A

PPO mold temperature 100-150℃ window has pitfalls at both ends; fine-tune according to defect type; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Extrusion & Post mold temperature windowdelaminationbubblewarpage

Q

PPO Wall Thickness 0.8mm Design Lower Limit

A

0.8mm is the red line of PPO wall thickness design; process cannot save structural design; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Processing Machinery wall thickness lower limitflowabilitymulti-gateshort shot

Q

PPO Melt Near-Newtonian Fluid Characteristics

A

PPO as a near-Newtonian fluid responds to temperature, not shear; raising temperature is the right way to reduce viscosity; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshootin...

Material Analysis near-Newtonian fluidtemperature sensitiveshearflow

Q

Pure PPO Melt 280-330℃ Window

A

Pure PPO temperature 280-330℃ is a hard window, MPPO is separately set at 260-285℃; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling pure PPOmelt temperaturein-mold stressMPPO

Q

PPO Melt Temperature Grading by Grade

A

PPO melt temperature follows the PPO content of the grade; changing material requires changing the temperature card; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting refer...

Material Analysis melt temperaturegrade gradingPPO contentmaterial change

Q

PPO Cumulative Drying Time Upper Limit

A

PPO cumulative drying is capped at 8 hours, and re-baking times must be recorded; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for subsequent similar problems

Material Drying cumulative drying8 hoursheat historyre-baking

이전 1 ... 694 695 696 697 698 699 700 ... 1164 다음

카테고리

전체 주제 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382