문제 및 해결책

일반적인 플라스틱 재료 문제에 대한 실질적인 답변

기사 둘러보기 →

Q

COC Cold Resistance Impact Failure

A

COC low-temperature brittleness is a boundary condition that must be evaluated in material selection; cold chain applications require special verification; room-temperature data cannot be extrapolated to low-temperature conditions.; After confirming effectiveness, fix the parameters and practices...

Material Analysis COC; low temperature; brittleness; impact; cold chain; failure

Q

COC Thick-walled Optical Part Long Molding Cycle

A

The cycle contradiction of COC thick-walled parts is resolved by variable mold temperature and structural design; the cost of blindly shortening cooling is deformation and cracking; cycle optimization should first calculate the heat balance.

Molds & Tooling COC; thick wall; cooling; cycle; variable mold temperature; deformation

Q

COC Grade Switchover Cross Contamination

A

The core of COC grade switchover is temperature difference management; the material change direction determines the risk type; standardized cleaning processes avoid human arbitrariness.; After confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Processing Machinery COC; grade switchover; contamination; Tg; purging; cleaning

Q

COC Medical Part Cleanliness Exceeding Standard

A

COC medical part cleanliness is a whole-chain project; the static adsorption characteristic requires stricter environmental control; ultrasonic cleaning is the key post-treatment to meet the standard.; After confirming effectiveness, fix the parameters and practices into the work instruction to p...

Molds & Tooling COC; medical; particle; cleanliness; static electricity; cleaning

Q

COC Obvious Ejector Pin Marks

A

COC ejector pin marks are the combined result of temperature and pressure; the ejection design of optical parts should prioritize function; local cooling enhancement is the most direct process means.; After confirming effectiveness, fix the parameters and practices into the work instruction to pr...

Molds & Tooling COC; ejector pin mark; ejection; cooling; optics; pressure

Q

COC Gate Mark and Jetting Mark

A

COC gate mark treatment mainly relies on multi-stage injection and gate design; the gate position of transparent parts should avoid the main viewing area at the design stage; shear control runs through the whole process.

Molds & Tooling COC; jetting mark; gate; multi-stage injection; snake pattern; transparent

Q

COC and PC Blending Delamination

A

COC's poor blending compatibility is the nature of the material; recycled material isolation management is the first line of defense; compatibilizer schemes must be verified by experiments and cannot be taken for granted.; After confirming effectiveness, fix the parameters and practices into the ...

Extrusion & Post COC; delamination; blending; compatibility; recycled material; interface

Q

COC Extruded Sheet Gel Particles

A

COC optical sheet gel particle prevention and control consists of three lines of defense: raw material, filtration and equipment; intermittent defects mostly originate from accumulated material in dead spots; screen management is a low-cost, high-yield measure.

Extrusion & Post COC; gel particle; extrusion; sheet; screen; gel

Q

COC Shrinkage Rate Estimation Deviation

A

COC low shrinkage is an advantage, but accurate values still depend on grade data; precision part molds should leave compensation allowance; the process sensitivity of amorphous materials cannot be ignored.

Molds & Tooling COC; shrinkage rate; dimension; grade; mold repair; precision

Q

COC Insufficient Verification for Glass Replacement

A

COC replacing glass is a dual verification project of regulation and performance; the 18~24 month re-certification cycle must be included in the project plan; data package completeness determines the success or failure of replacement.

Material Analysis COC; glass replacement; pharmaceutical packaging material; verification; regulation; migration

이전 1 ... 995 996 997 998 999 1000 1001 ... 1164 다음

카테고리

전체 주제 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382