Problem & Solution

Practical answers to common plastic material challenges

Browse Articles →

Q

PVC Post-drying Management

A

PVC powder used immediately after drying, not overnight; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar problems later

Material Drying PVC powder moisture regain re-drying

Q

PVC Drying Temperature Upper Limit

A

PVC drying is a low-temperature short-time route, over-temperature consumes stabilizer; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar problems later

Material Drying PVC drying temperature heat stabilizer yellowing

Q

PVC Drying Necessity

A

PVC drying requirement is not high but cannot be omitted across the board; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar problems later

Material Drying PVC drying water absorption silver streak

Q

PVC Drying 75-90℃

A

PVC drying requirement is lower than nylon but cannot be omitted; 75-90℃×1.5-2.5h is the general specification, moisture-affected material must be re-dried; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Material Drying PVC; drying; 75-90℃; silver streak; bubble

Q

PVC Injection Silver Streaks

A

PVC silver streaks = 'moisture + decomposition gas': besides moisture, PVC silver streaks also have the factor of shear decomposition gas; water control and shear heat control must go together; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent r...

Material Drying PVC; '2079851475616104452; silver streak; moisture; shear heat

Q

PVC Dry Blend Stratification

A

PVC dry blend = 'homogeneity management': particle size matching and moisture-proofing are key; dry blend stratification is a hidden quality fluctuation source, storage and transport must be managed well; after confirming effectiveness, fix the parameters and practices into the work instruction t...

Material Drying PVC; dry blend; stratification; moisture absorption; storage

Q

PVC Regrind Use Problems

A

PVC regrind = 'stabilizer reserve discounted': use less and cautiously, and add stabilizer; PVC regrind's heat history directly determines remaining stability, multiple reuse risk is extremely high.

Material Drying PVC; regrind; yellowing; stabilizer; heat history

Q

PVC '2079851475616104458 Bubbling

A

PVC '2079851475616104458 bubbling = 'moisture and volatiles': sheet pre-drying and moisture-proof storage are key; old stock sheets especially must be moisture-tested before going on line; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurr...

Material Drying PVC; '2079851475616104458; bubbling; moisture; storage

Q

PVC Equipment Corrosion

A

PVC corrosion = an 'HCl management' problem: shutdown replacement is an iron rule; corrosion is irreversible equipment damage — corrosion-resistant materials + standardized shutdown are far more economical than replacing screws afterwards; prevent before it happens.

Material Drying PVC; corrosion; HCl; screw; shutdown replacement

Q

PVB Glass Cleaning and Drying

A

Surface preparation for PVB-glass adhesion is the foundation; cleaning and drying is the premise; inspection ensures quality.; After confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Material Drying PVB;glass;cleaning;drying;adhesion;surface

Prev 1 ... 62 63 64 65 66 67 68 ... 144 Next

Categories

All Topics 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382