Problem & Solution

Practical answers to common plastic material challenges

Browse Articles →

Q

POM Sink Mark Depression

A

POM sink mark control prioritizes holding pressure with structure as backstop; gate position and rib design are the fundamental countermeasures on the mold side; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling POM;sink mark;holding pressure;gate position;rib

Q

POM Short Shot Troubleshooting

A

POM short shot troubleshooting goes equipment first, process second; the three checks of bridging, check valve, and cushion are the fixed opening moves; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling POM;short shot;check valve;bridging;cushion

Q

POM Demolding Sticking

A

The counterintuitive point of POM demolding is that too shiny means sticking; moderate surface texture plus sufficient draft is more reliable than mirror polishing; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling POM;demolding;mold sticking;draft angle;surface texture

Q

POM Residual Stress Testing

A

The hydrochloric acid soaking method is the on-site touchstone for POM stress; it turns hidden stress into visible cracks, achieving preventive screening; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling POM;residual stress;hydrochloric acid soaking;crack;testing

Q

POM Warpage from Uneven Cooling

A

POM warpage control starts from DFM; cooling balance and holding pressure window are the process mainline, and dimensional drift is backstopped by post-treatment; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling POM;warpage;uneven cooling;DFM;CMM

Q

POM Weld Line Strength

A

POM weld line management relies on moving design forward; high mold temperature and gate layout optimization transfer the weak line to non-critical areas; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling POM;weld line;gate position;high mold temperature;fatigue

Q

POM Vent Groove 0.013-0.025mm

A

POM venting is a tightrope walk between deep and shallow; 0.013mm-level precision plus regular cleaning can take care of both ends; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling POM;vent groove;0.013mm;burnt;flash

Q

POM Shrinkage Rate 1.8-3.5%

A

POM's shrinkage ranks among the highest in engineering plastics; uniform wall thickness, holding pressure compensation, and mold margin allowance are the three key elements of dimensional control; after confirming effectiveness, solidify the parameters and practices into the work instruction to p...

Molds & Tooling POM;shrinkage rate;1.8-3.5%;holding pressure;uniform wall thickness

Q

POM conveyor chain plate

A

POM chain plates are the benchmark for fatigue applications; pin hole reinforcement and life cycle management make a million cycles well-founded; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling POM；chain plate；fatigue；pin hole；wear

Q

POM zipper fasteners

A

POM fasteners have small size but big risk; structural rounding, grade toughening, and demolding protection are the triple defense lines; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling POM；zipper；fastener；low temperature；brittle fracture

Prev 1 ... 57 58 59 60 61 62 63 ... 151 Next

Categories

All Topics 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382