Sorun ve Çözüm

Yaygın plastik malzeme zorluklarına pratik yanıtlar

Makalelere Göz At →

TPU silver streaks

TPU silver streaks have the same source as bubbles but to a lesser degree; troubleshoot the three aspects of drying, mixing, and cold material; cold slug wells are a simple and effective measure to intercept cold material; after confirming effectiveness, fix the parameters and practices into the ...

Material Drying TPU；silver streak；moisture；mixing；cold material；cold slug well

2 görüntüleme

Tam Yanıtı Oku →

TPU bubbles (air trap and degradation type)

Bubble identification must be divided into four categories: moisture, air trap, degradation, and vacuum bubbles; after drying is ineffective, troubleshoot the remaining sources one by one according to position characteristics; after confirming effectiveness, fix the parameters and practices into ...

Material Drying TPU；bubble；air trap；degradation；vacuum bubble；venting

2 görüntüleme

Tam Yanıtı Oku →

TPU bubbles (moisture type)

Eighty percent of TPU bubbles originate from moisture management; meeting the drying standard is only the first step, and controlling the exposure time after drying is equally critical; repeated heating cannot replace drying.

Material Drying TPU；bubble；moisture；drying；moisture content；moisture absorption

2 görüntüleme

Tam Yanıtı Oku →

TPE overmolding bubbles

For overmolding bubbles check moisture and venting; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar problems later

Material Drying TPEovermoldingbubbleventing

2 görüntüleme

Tam Yanıtı Oku →

TPE silver streak moisture

For silver streaks check moisture first; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar problems later

Material Drying TPEsilver streakmoistureshear

2 görüntüleme

Tam Yanıtı Oku →

TPE bubble causes

Bubbles are identified and handled by three routes; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar problems later

Material Drying TPEbubblethree routesidentification

2 görüntüleme

Tam Yanıtı Oku →

TPE first article verification

TPE first article verification must include material state and bonding; qualified appearance does not mean qualified function; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Material Drying TPE；first article verification；moisture content；bonding；material change

2 görüntüleme

Tam Yanıtı Oku →

TPE uneven color

TPE color matching relies on carrier compatibility and back pressure dispersion; coupling agents are a chemical means to improve bonding; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Material Drying TPE；uneven color；color masterbatch；back pressure；coupling agent

2 görüntüleme

Tam Yanıtı Oku →

TPE silver streaks dominated by moisture

For TPE silver streaks, suspect drying first; the 0.1% red line plus an insulated hopper can eliminate 95% of silver streaks; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Material Drying TPE；silver streak；moisture；0.1%；drying

2 görüntüleme

Tam Yanıtı Oku →

TPE bubble cause differentiation

TPE bubble troubleshooting must consider both soft and hard plastics; dual-'2079851475616104451 is a special requirement for overmolded parts; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Material Drying TPE；bubble；moisture；air entrainment；overmolding

2 görüntüleme

Tam Yanıtı Oku →

Önceki 1 ... 57 58 59 60 61 62 63 ... 144 Sonraki

Kategoriler

Tüm Konular 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382

Sorun ve Çözüm

Kategoriler

Teklif Al