Sorun ve Çözüm

Yaygın plastik malzeme zorluklarına pratik yanıtlar

Makalelere Göz At →

PSU Notch Sensitivity and Fracture

PSU notch sensitivity requires an absolute fillet principle in design; arc transition is a zero-cost strength improvement; stress management coordinates with structural design.; After confirming effectiveness, solidify the parameters and practices into the work instructions to prevent recurrence

Molds & Tooling PSU; notch; fracture; fillet; stress concentration; design

2 görüntüleme

Tam Yanıtı Oku →

PSU Wall Thickness Design Constraints

PSU wall thickness constraints are hard boundaries determined by material flowability; the 1.5mm bottom line cannot be broken; advancing design review avoids mold waste.; After confirming effectiveness, solidify the parameters and practices into the work instructions to prevent recurrence

Molds & Tooling PSU; wall thickness; flow length ratio; 1.5mm; design; flowability

2 görüntüleme

Tam Yanıtı Oku →

PSU Surface Scratches and Chipping

PSU surface protection starts with mold finish; processing and transfer links are high-incidence areas for damage; the appearance standards of transparent parts need whole-chain guarantee.; After confirming effectiveness, solidify the parameters and practices into the work instructions to prevent...

Molds & Tooling PSU; scratches; chipping; surface finish; transfer; protection

2 görüntüleme

Tam Yanıtı Oku →

Contamination by Decomposed Material After PSU Shutdown

The core of PSU shutdown management is thorough removal of decomposed material; the choice of purging material is particular; the purge amount when resuming production must be sufficient.; After confirming effectiveness, solidify the parameters and practices into the work instructions to prevent ...

Molds & Tooling PSU; shutdown; decomposition; cleaning; impurities; purging

2 görüntüleme

Tam Yanıtı Oku →

PSU Nozzle Drool and Cold Slug

The high-viscosity characteristic of PSU allows large-orifice nozzle design; extended heated nozzles are standard; fine temperature management avoids both extremes.; After confirming effectiveness, solidify the parameters and practices into the work instructions to prevent recurrence

Molds & Tooling PSU; nozzle; drool; cold slug; extended type; orifice

2 görüntüleme

Tam Yanıtı Oku →

Gate Marks on PS Products

Gate mark management relies on coordination between design and process.; After confirming effectiveness, solidify the parameters and practices into the work instructions to prevent recurrence; Include this case in the defect archive as a reference for troubleshooting similar problems in the future

Molds & Tooling PS; gate mark; trimming; edge chipping; submarine gate

2 görüntüleme

Tam Yanıtı Oku →

Mold Temperature Selection for PS Products

Mold temperature selection is a balance between quality and efficiency; product requirements determine priorities.; After confirming effectiveness, solidify the parameters and practices into the work instructions to prevent recurrence; Include this case in the defect archive as a reference for tr...

Molds & Tooling PS; mold temperature; selection; stress; cycle

2 görüntüleme

Tam Yanıtı Oku →

Mold Venting for PS Products

Venting design for transparent parts must be more adequate; burn marks are the indication for adding venting.; After confirming effectiveness, solidify the parameters and practices into the work instructions to prevent recurrence; Include this case in the defect archive as a reference for trouble...

Molds & Tooling PS; venting; burning; trapped air; transparent parts

2 görüntüleme

Tam Yanıtı Oku →

PS Product Gate Design

The gate is the weak link of PS products; attention should be paid to both design and post-processing.; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for simi...

Molds & Tooling PS;gate;stress concentration;cracking;design

2 görüntüleme

Tam Yanıtı Oku →

PS Product Demolding Draft Design

PS mold draft should take the upper limit; conservative demolding design is advisable for brittle materials.; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PS;demolding draft;scratch;mold;design

2 görüntüleme

Tam Yanıtı Oku →

Önceki 1 ... 40 41 42 43 44 45 46 ... 151 Sonraki

Kategoriler

Tüm Konular 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382

Sorun ve Çözüm

Kategoriler

Teklif Al