Sorun ve Çözüm

Yaygın plastik malzeme zorluklarına pratik yanıtlar

Makalelere Göz At →

PP Cooling Time Setting

PP cooling is calculated by wall thickness; post-crystallization deformation must be prevented; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar futu...

Molds & Tooling cooling time crystallization demolding cycle

2 görüntüleme

Tam Yanıtı Oku →

PP Long Glass Fiber LFT Processing

LFT-PP preserves fiber length; low shear and large gates; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar future problems

Molds & Tooling LFT long glass fiber shear fiber length

2 görüntüleme

Tam Yanıtı Oku →

PP Gate Size Design

PP gates must be large enough to feed the large shrinkage; submarine pin-point gates for appearance parts; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for s...

Molds & Tooling gate feeding sink mark size

2 görüntüleme

Tam Yanıtı Oku →

PP Draft Angle Design

PP's large shrinkage means strong clamping; draft angle starts at 1-2°; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar future problems

Molds & Tooling draft angle shrinkage scratching polishing

2 görüntüleme

Tam Yanıtı Oku →

PP Shrinkage 1.0-2.5 Management

PP shrinkage 1.0-2.5% is a wide range; actual measurement compensation and locked process; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar future pr...

Molds & Tooling shrinkage dimension wall thickness crystallization

2 görüntüleme

Tam Yanıtı Oku →

PP Mold Temperature and Crystallization

PP mold temperature 30-60°C is normal; take the upper limit for crystallization strength; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar future pro...

Molds & Tooling mold temperature crystallization cycle strength

2 görüntüleme

Tam Yanıtı Oku →

PP Glass Fiber Reinforced Processing

For PP glass fiber material, upper-limit temperature and reduced speed, wear-resistant equipment; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar fu...

Molds & Tooling glass fiber melt temperature rotation speed wear resistance

2 görüntüleme

Tam Yanıtı Oku →

PP Vent Groove Design

PP venting 0.02-0.04mm; shallow traps air and deep causes flash; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar future problems

Molds & Tooling vent groove air entrapment flash depth

2 görüntüleme

Tam Yanıtı Oku →

PP Gate 50/60 Rule

The 50/60 rule for PP gates is a design standard; position and size are equally important; ensure feeding and prevent sink marks.; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PP; gate; 50/60 rule; wall thickness; feeding; sink mark

2 görüntüleme

Tam Yanıtı Oku →

PP Draft Angle 1-2°

PP draft angle is a design specification; textured surface compensation; ejection and surface are equally important.; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PP; draft angle; 1-2°; texture; ejection; deformation

2 görüntüleme

Tam Yanıtı Oku →

Önceki 1 ... 44 45 46 47 48 49 50 ... 151 Sonraki

Kategoriler

Tüm Konular 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382

Sorun ve Çözüm

Kategoriler

Teklif Al