Wrinkling (folds, excessive sagging)

In the '2079851475616104458 (vacuum forming) production process, the product exhibits the quality defect of "Wrinkling (folds, excessive sagging)". The specific manifestation is that the sheet sags excessively after heating, producing folds. This defect is relatively common when processing materials such as PP, PS, PET, PVC, ABS sheets, and its occurrence conditions are usually related to the unreasonable settings of sheet heating temperature, forming pressure/vacuum level, mold temperature, and cooling time. When the "Wrinkling (folds, excessive sagging)" situation is severe, it will cause a series of chain quality defects in the product in terms of appearance, dimensional accuracy, mechanical properties, etc., which not only reduces the functionality and safety of the product in use, but also directly increases the scrap rate and production cost. Therefore, this problem requires systematic diagnosis and optimization from multiple dimensions such as material selection, the status of the '2079851475616104458 machine, heating oven, mold, and vacuum/air pressure system, and sheet heating temperature, forming pressure/vacuum level, mold temperature, and cooling time.

1. Heating temperature too high. Temperature is the core factor affecting melt fluidity and viscosity. A temperature set too high will cause the melt viscosity to decrease, insufficient melt strength, and even thermal degradation; a temperature that is too low results in poor melt fluidity and insufficient plasticization, making it impossible to fill or form smoothly. A reasonable temperature window should be optimized and determined within the recommended range according to the melting characteristics and thermal stability of the material. 2. Sheet support spacing too large. This factor causing the problem reflects that certain process conditions or material characteristics in '2079851475616104458 (vacuum forming) processing have not met the optimal molding requirements. Such problems are often cumulative and hidden, and should be investigated and verified as key focus items during process debugging and finalization to ensure that hidden dangers are eliminated at the source. 3. Heating time too long. This factor causing the problem reflects that certain process conditions or material characteristics in '2079851475616104458 (vacuum forming) processing have not met the optimal molding requirements. Such problems are often cumulative and hidden, and should be investigated and verified as key focus items during process debugging and finalization to ensure that hidden dangers are eliminated at the source. In terms of equipment maintenance, the regular overhaul and precision confirmation of the '2079851475616104458 machine, heating oven, mold, and vacuum/air pressure system are not in place, causing the actual operating parameters of the equipment to deviate from the process requirements, which will also become a potential inducement of the "Wrinkling (folds, excessive sagging)" problem.

1. Reduce the heating temperature. Adjustments should follow the principle of gradual progress; the amplitude of each adjustment should not be too large, and it is recommended to decrease by 5%~15% of the current value. After each adjustment, observe the product quality changes stably for at least 5~10 mold cycles, and continue adjusting only after confirming that the improvement direction is correct; avoid one-step excessive adjustment. 2. Reduce the support spacing. Adjustments should follow the principle of gradual progress; the amplitude of each adjustment should not be too large, and it is recommended to decrease by 5%~15% of the current value. After each adjustment, observe the product quality changes stably for at least 5~10 mold cycles, and continue adjusting only after confirming that the improvement direction is correct; avoid one-step excessive adjustment. 3. Shorten the heating time. Adjustments should follow the principle of gradual progress; the amplitude of each adjustment should not be too large, and it is recommended to decrease by 5%~15% of the current value. After each adjustment, observe the product quality changes stably for at least 5~10 mold cycles, and continue adjusting only after confirming that the improvement direction is correct; avoid one-step excessive adjustment. In terms of material management, incoming inspection of raw materials upon arrival and in-process inspection of work-in-progress should be strengthened, and the key performance indicators of PP, PS, PET, PVC, ABS sheets should be strictly controlled to ensure the stability of molding quality from the source.

In summary, the causes of the "Wrinkling (folds, excessive sagging)" problem can be attributed to the combined action of multiple factors such as Heating temperature too high, Sheet support spacing too large. Solving this problem requires starting from aspects such as Reduce the heating temperature, Reduce the support spacing and adopting systematic governance measures. In actual production, it is recommended to establish a prevention and rapid response mechanism for this problem, and achieve stable production and continuous improvement through sheet heating uniformity and stretch ratio control.