Gel particles on the preform surface (fisheyes)

In the stretch '2079851475616104457 production process, the product exhibits the quality defect of "Gel particles on the preform surface (fisheyes)".The specific manifestation is Transparent gel particles appear on the preform surface.This defect is more common when processing materials such as PET, PP and PC, and its occurrence is usually related to unreasonable settings of stretching temperature, stretch ratio, blowing pressure and preform heating uniformity.When the Gel particles on the preform surface (fisheyes) situation is severe, it will cause a series of chain quality defects in the product's appearance, dimensional accuracy, mechanical properties and other aspects, which not only reduces the product's functionality and safety in use, but also directly increases the scrap rate and production cost.Therefore, this problem requires systematic diagnosis and optimization from multiple dimensions such as material selection, the status of the stretch '2079851475616104457 machine, heating oven, stretch rod and blow mold, and stretching temperature, stretch ratio, blowing pressure and preform heating uniformity.

1. Incomplete PET plasticization.This factor causing the problem reflects that certain process conditions or material properties in stretch '2079851475616104457 do not meet the optimal forming requirements.Such problems are often cumulative and concealed, and should be investigated and verified as key focus items during process debugging and finalization to ensure hidden dangers are eliminated at the source. 2. High-melting-point impurities mixed into the raw material.Material selection and handling are the foundation of forming quality.The intrinsic properties of the resin such as molecular weight, molecular weight distribution and melt index determine its processing window and final performance.Factors such as excessive moisture content of raw materials, mixed impurities and improper regrind ratios will all cause various defects during processing. In addition, the insufficient overall coordination of preform heating uniformity and biaxial stretch orientation control is also a factor that cannot be ignored; there are complex interactions and coupling relationships among the process parameters, and the deviation of any parameter may aggravate the degree of Gel particles on the preform surface (fisheyes) through chain effects. In terms of equipment maintenance, the regular overhaul and accuracy confirmation of the stretch '2079851475616104457 machine, heating oven, stretch rod and blow mold are not in place, causing the actual operating parameters of the equipment to deviate from process requirements, which will also become a potential inducement of the Gel particles on the preform surface (fisheyes) problem.

1. Raise the plasticization temperature.When implementing adjustments, it is recommended to use the single-factor variable method, adjusting only one parameter at a time and fully evaluating the effect, to avoid simultaneous changes of multiple parameters making the cause of the problem untraceable.The adjustment amplitude should be small rather than large; each adjustment is recommended to be controlled within 5%~10% of the original value, and after adjustment run stably for at least 3~5 mold cycles to observe the effect. 2. Check raw material purity.Inspection work should establish a standardized checklist, specifying inspection items, technical standards, inspection frequency and responsible persons.Key equipment components should be regularly disassembled to check the condition of hidden parts, and judgment should not be based solely on operating appearance.Inspection results should be recorded in detail and a trend analysis mechanism established to predict potential failures. 3. Use a fine screen.Before introducing new tools, new materials or new methods, sufficient applicability evaluation and small-batch verification should be carried out.It is recommended to first conduct offline tests or simulation analyses outside production conditions, and introduce them into the formal production line only after confirming effectiveness and safety.Keep proper change management records to facilitate subsequent traceability and experience accumulation. In terms of material management, incoming inspection of raw materials and in-process testing of work-in-progress should be strengthened, and key performance indicators of PET, PP and PC should be strictly controlled to ensure the stability of forming quality from the source.

In summary, the causes of the "Gel particles on the preform surface (fisheyes)" problem can be attributed to the combined action of multiple factors such as Incomplete PET plasticization, High-melting-point impurities mixed into the raw material.To solve this problem, it is necessary to start from aspects such as Raise the plasticization temperature, Check raw material purity and take systematic governance measures.In actual production, it is recommended to establish a prevention and rapid response mechanism for this problem, achieving stable production and continuous improvement through preform heating uniformity and biaxial stretch orientation control.