المشاكل والحلول

إجابات عملية على التحديات الشائعة في مواد البلاستيك

تصفح المقالات →

Q

PA6 Insert Root Cracking

A

Insert cracking is controlled by the three of preheating, wall thickness and stress relief; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar pro...

Injection Molding PA6 metal insert cracking preheating

Q

PA6 Floating Fiber Improvement

A

Floating fiber treatment relies on high temperature and high speed to ensure resin coating, and grade selection is also very important; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as...

Injection Molding PA6 floating fiber glass fiber exposure mold temperature

Q

PA6 Burnt Trapped-Air Treatment

A

Burnt is the result of trapped air and adiabatic compression, and venting structure is the radical means; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference f...

Injection Molding PA6 burnt trapped air venting insert

Q

PA6 Injection Speed Strategy

A

PA6 injection speed strategy must be set separately by grade; neat material seeks speed, reinforced material seeks stability, and temperature is the regulating valve between the two; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Injection Molding PA6; injection speed; jetting mark; reinforced grade; surface quality

Q

PA6 Powder Sintering

A

SLS part performance relies on process parameter and powder management optimization, and post-processing improves appearance; after confirming effectiveness, fix the parameters and practices into the work instructions to prevent recurrence

Injection Molding PA6SLSlaser sinteringpowder

Q

PA6 Nozzle Drooling Treatment

A

Low-viscosity PA6 drooling must be treated by a combination of nozzle structure and suck-back process; after confirming effectiveness, fix the parameters and practices into the work instructions to prevent recurrence; include this case in the defect archive as a reference for troubleshooting simi...

Injection Molding PA6droolingneedle valve nozzlesuck-back

Q

PA66 injection pressure window

A

PA66 pressure setting should be tailored to the part; trial-mold finalization plus scientific transfer points adapt to fluctuations better than empirical parameters; after confirming effectiveness, fix the parameters and practices into the work instructions to prevent recurrence

Injection Molding PA66；injection pressure；75-125MPa；reinforced grade；pressure transfer

Q

PA66 injection speed strategy

A

PA66 injection speed follows grade-specific strategies; pure material seeks speed, reinforced seeks stability, and temperature is the compensation valve between the two; after confirming effectiveness, fix the parameters and practices into the work instructions to prevent recurrence

Injection Molding PA66；injection speed；reinforced grade；surface quality

Q

PA66 glass fiber floating fiber surface

A

Floating fiber treatment requires both process and material routes in parallel; high mold temperature plus velocity matching is the main line, and demanding appearance parts are more thoroughly solved from the formulation end; after confirming effectiveness, fix the parameters and practices into ...

Injection Molding PA66；floating fiber；injection speed；mold temperature；surface

Q

PA66 flash clamping force calculation

A

PA66 flash treatment uses three approaches together: clamping force calculation, pressure control, and parting line maintenance; increasing pressure alone will only accelerate mold damage; after confirming effectiveness, fix the parameters and practices into the work instructions to prevent recur...

Injection Molding PA66；flash；clamping force；parting line；low viscosity

السابق 1 ... 127 128 129 130 131 132 133 ... 151 التالي

الفئات

جميع المواضيع 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382