Insufficient drying of the raw material

During the injection '2079851475616104457 production process, the product exhibits the quality defect of "Insufficient drying of the raw material". Specifically manifested as the moisture content of the raw material exceeding the standard. This defect is relatively common when processing materials such as PET, PP, HDPE, and PS, and its occurrence conditions are usually related to unreasonable settings of injection pressure, parison temperature, blowing air pressure, and mold temperature. When the Insufficient drying of the raw material situation is severe, it will cause a series of chain-reaction quality defects in the product in terms of appearance, dimensional accuracy, mechanical properties, etc., which not only reduces the usability and safety of the product, but also directly increases the scrap rate and production cost. Therefore, this problem requires systematic diagnosis and optimization from multiple dimensions, including material selection, the condition of the injection '2079851475616104457 machine, core rod, parison mold, blow mold, and transfer mechanism, as well as injection pressure, parison temperature, blowing air pressure, and mold temperature.

1. Drying temperature insufficient. Temperature is the core factor affecting melt fluidity and viscosity. Setting the temperature too high will cause the melt viscosity to decrease, insufficient melt strength, and even thermal degradation; if the temperature is too low, the melt fluidity is poor and plasticization is insufficient, making it impossible to fill or mold smoothly. A reasonable temperature window should be optimally determined within the recommended range according to the melting characteristics and thermal stability of the material. 2. Insufficient drying time. This factor leading to the problem reflects that certain process conditions or material properties in injection blow '2079851475616104453ing have not met the optimal molding requirements. Such problems often have cumulative and hidden characteristics, and should be investigated and verified as key focus items during process debugging and finalization to ensure that hidden dangers are eliminated from the source. 3. Dehumidifier failure. This factor leading to the problem reflects that certain process conditions or material properties in injection blow '2079851475616104453ing have not met the optimal molding requirements. Such problems often have cumulative and hidden characteristics, and should be investigated and verified as key focus items during process debugging and finalization to ensure that hidden dangers are eliminated from the source. In terms of equipment maintenance, inadequate regular overhaul and accuracy confirmation of the injection '2079851475616104457 machine, core rod, parison mold, blow mold, and transfer mechanism cause the actual operating parameters of the equipment to deviate from the process requirements, which can also become a potential inducement of the Insufficient drying of the raw material problem.

1. Increase the drying temperature and extend the time. When implementing adjustments, it is recommended to adopt the single-factor variable method, adjusting only one parameter at a time and fully evaluating the effect, to avoid multiple parameters changing simultaneously making the cause of the problem untraceable. The adjustment magnitude should be small rather than large; each adjustment is recommended to be controlled within 5%~10% of the original value, and after adjustment, run stably for at least 3~5 mold cycles to observe the effect. 2. Inspect and repair the dehumidifier. Equipment maintenance should establish a three-level preventive maintenance system: daily spot checks, regular maintenance, and planned overhauls. The operating data and wear trends of key components should be continuously statistically analyzed, and the probability and time window of potential failures should be predicted through condition monitoring, transforming passive fault repair into active condition-based maintenance. 3. Regularly test the moisture content. Inspection work should establish a standardized inspection checklist, clarifying the inspection items, technical standards, inspection frequency, and responsible persons. Key equipment components should be regularly disassembled to inspect the condition of hidden parts, and judgment should not be based solely on operating appearance. Inspection results should be recorded in detail and a trend analysis mechanism established to predict potential failures. In terms of material management, incoming inspection of raw materials and in-process inspection of work-in-progress should be strengthened, and the key performance indicators of PET, PP, HDPE, and PS should be strictly controlled to ensure the stability of molding quality from the source.

In summary, the causes of the "Insufficient drying of the raw material" problem can be attributed to the combined action of multiple factors such as drying temperature insufficient and insufficient drying time. Solving this problem requires starting from aspects such as increase the drying temperature and extend the time and inspect and repair the dehumidifier, and adopting systematic governance measures. In actual production, it is recommended to establish a prevention and rapid response mechanism for this problem, achieving stable production and continuous improvement through parison wall thickness uniformity and transfer temperature control.