문제 및 해결책

일반적인 플라스틱 재료 문제에 대한 실질적인 답변

기사 둘러보기 →

Q

ABAK warpage deformation

A

ABAK warpage improvement is an advantage over pure PA; however, process management is still necessary; uniformity is the core.; After confirming effectiveness, fix the parameters and practices into the work instructions to prevent recurrence

Molds & Tooling ABAK；warpage；crystallization；mold temperature；holding pressure；wall thickness

Q

ABAK surface gloss

A

The matte characteristic of ABAK is an advantage for automotive interiors; uniformity depends on dispersion quality; inspection ensures consistency.; After confirming effectiveness, fix the parameters and practices into the work instructions to prevent recurrence

Molds & Tooling ABAK；surface gloss；matte；dispersion；mold temperature；interior trim

Q

ABAK flowability management

A

ABAK flowability and compatibility trade off against each other; optimized compatibilizer dosage is the key; grades and processes compensate for flowability.; After confirming effectiveness, fix the parameters and practices into the work instructions to prevent recurrence

Material Analysis ABAK；flowability；compatibilizer；viscosity；grade；temperature

Q

ABAK heat resistance balance

A

ABAK heat resistance is a function of the ratio; glass fiber reinforcement is the improvement means; actual measurement verification is more reliable than theoretical estimation.; After confirming effectiveness, fix the parameters and practices into the work instructions to prevent recurrence

Molding Process ABAK；heat resistance；heat deflection temperature；ratio；glass fiber；actual measurement

Q

ABAK impact strength improvement

A

ABAK impact strength improvement depends on ratio and compatibilizer optimization; more ABS is not always better; testing verifies the actual improvement effect.; After confirming effectiveness, fix the parameters and practices into the work instructions to prevent recurrence

Material Drying ABAK；impact strength；low temperature；ratio；compatibilizer；toughness

Q

ABAK dimensional stability improvement

A

ABAK dimensional stability is a significant improvement over pure PA; however, precise management of shrinkage and water absorption is still necessary; wet-state verification covers the service environment.; After confirming effectiveness, fix the parameters and practices into the work instructio...

Molds & Tooling ABAK；dimensional stability；shrinkage rate；water absorption；mold；wet state

Q

ABAK processing temperature window

A

The ABAK temperature window is the intersection of the thermal properties of the two components; PA6-based is easier to process than PA66-based; actual measured temperature is the process benchmark.; After confirming effectiveness, fix the parameters and practices into the work instructions to pr...

Molding Process ABAK；processing temperature；window；PA6；PA66；degradation

Q

ABAK insufficient drying bubbles and silver streaks

A

ABAK drying management must be carried out according to the strict standards of the PA component; 4~6 hours is the alloy drying benchmark; moisture verification cannot be omitted.; After confirming effectiveness, fix the parameters and practices into the work instructions to prevent recurrence

Material Drying ABAK；drying；silver streak；bubbles；moisture absorption；PA component

Q

ABAK poor compatibility delamination

A

The compatibility of ABAK is the decisive factor for alloy performance; 3~8% compatibilizer is the patent-verified optimized range; commercial grades are more reliable than self-blending.; After confirming effectiveness, fix the parameters and practices into the work instructions to prevent recur...

Extrusion & Post ABAK；compatibility；delamination；ABS-g-MAH；SMA；phase separation

Q

Cold flow-creep superposition effect of ultra-large PTFE sintered parts

A

This problem requires comprehensive analysis from multiple dimensions of material, process, equipment, and operation, and should be solved by systematically optimizing process parameters and the quality control system.

Processing Machinery PTFE，sintering temperature，deformation

이전 1 ... 1042 1043 1044 1045 1046 1047 1048 ... 1164 다음

카테고리

전체 주제 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382