문제 및 해결책

일반적인 플라스틱 재료 문제에 대한 실질적인 답변

기사 둘러보기 →

Q

HDPE '2079851475616104452 cycle optimization

A

The boundary of HDPE cycle optimization is sufficient cooling; tapping potential in other links is safer than compressing cooling; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Injection Molding HDPE; cycle; cooling time; deformation; optimization

Q

HDPE film blowing temperature

A

Stable film blowing temperature is the prerequisite for film bubble stability; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for similar future problems

Extrusion & Post HDPEfilm blowingtemperaturefilm bubble

Q

HDPE holding pressure shrinkage compensation management

A

HDPE holding pressure is graded by wall thickness; gate freeze-off analysis is the scientific method to determine the holding time; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Production & Quality HDPE; holding pressure; 60-80%; 2-5 seconds; freeze-off

Q

HDPE injection speed control

A

HDPE speed strategy is based on medium speed; the balance between shear and flow marks is achieved by a segmented speed curve; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Injection Molding HDPE; injection speed; medium speed; shear; flow mark

Q

HDPE mold temperature 20-60℃

A

HDPE mold temperature is the balance point between efficiency and quality; uniform cooling is more important than the absolute temperature value; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling HDPE; mold temperature; 20-60℃; crystallization; uniform cooling

Q

HDPE melt temperature 200-280℃

A

HDPE's wide temperature window is its processing advantage; but it also degrades above 280℃, and being lenient does not mean having no boundary; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Injection Molding HDPE; melt temperature; 200-240℃; 280℃; degradation

Q

HDPE low water absorption drying

A

HDPE drying is moisture protection rather than dehydration; sealed storage is the main measure, and humid material is remedied at 80-90℃×2h; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Material Drying HDPE; drying; non-hygroscopic; 80-90℃; silver streak

Q

HDPE film insufficient screw mixing

A

Film has the highest requirements for melt uniformity; screw design is the equipment foundation of gel particle control.; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Processing Machinery HDPE; film; screw; mixing; gel particle; barrier

Q

HDPE film improper barrel water cooling

A

Barrel cooling is a neglected factor affecting output; standardized water cooling management can stabilize conveying efficiency.; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Extrusion & Post HDPE; film; barrel; water cooling; output; conveying

Q

HDPE film PPA eliminating die lip buildup

A

PPA is a highly efficient means of eliminating die lip buildup; it takes effect at a low addition amount, but attention should be paid to uniform dispersion and onset time.; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling HDPE; film; PPA; die lip buildup; processing aid; lubrication

이전 1 ... 976 977 978 979 980 981 982 ... 1164 다음

카테고리

전체 주제 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382