Bubble lines on the parison surface

During the injection '2079851475616104457 production process, the product exhibits the quality defect of "Bubble lines on the parison surface". Specifically manifested as bubble lines along the flow direction appearing on the parison surface. This defect is relatively common when processing materials such as PET, PP, HDPE, and PS, and its occurrence conditions are usually related to unreasonable settings of injection pressure, parison temperature, blowing air pressure, and mold temperature. When the Bubble lines on the parison surface situation is severe, it will cause a series of chain-reaction quality defects in the product in terms of appearance, dimensional accuracy, mechanical properties, etc., which not only reduces the usability and safety of the product, but also directly increases the scrap rate and production cost. Therefore, this problem requires systematic diagnosis and optimization from multiple dimensions, including material selection, the condition of the injection '2079851475616104457 machine, core rod, parison mold, blow mold, and transfer mechanism, as well as injection pressure, parison temperature, blowing air pressure, and mold temperature.

1. Volatile gases present in the raw material. The selection and handling of materials is the foundation of molding quality. The intrinsic characteristics of the resin, such as molecular weight, molecular weight distribution, and melt index, determine its processing window and final performance. Factors such as excessive moisture content of the raw material, mixing in of impurities, and improper proportion of regrind will all trigger various defects during processing. 2. Injection speed too fast. Speed parameters affect the flow state and time allocation of the melt during the '2079851475616104453. A speed that is too slow leads to premature cooling and insufficient filling; a speed that is too fast causes melt fracture, air entrapment, and shear overheating. The optimization of the speed curve should make the melt flow smoothly and orderly in the cavity. In addition, insufficient overall coordination between parison wall thickness uniformity and transfer temperature control is also a factor that cannot be ignored; there are complex interactions and coupling relationships among the various process parameters, and the deviation of any single parameter may aggravate the degree of Bubble lines on the parison surface through chain effects. In terms of equipment maintenance, inadequate regular overhaul and accuracy confirmation of the injection '2079851475616104457 machine, core rod, parison mold, blow mold, and transfer mechanism cause the actual operating parameters of the equipment to deviate from the process requirements, which can also become a potential inducement of the Bubble lines on the parison surface problem.

1. Fully dry the raw material. Raw '2079851475616104451 should select a matching type of drying equipment according to the resin type and water absorption characteristics, and reasonably set the drying temperature, drying time, and dew point indicators. The dried raw material should be put into production use as soon as possible; if temporary storage is required, it should be kept in a sealed container in a dry environment (dew point below -30℃). Regularly test the drying effect to ensure that the moisture content meets the standard. 2. Reduce the injection speed. Adjustments should follow the principle of gradual progress; the magnitude of each adjustment should not be too large, and it is recommended to decrease in steps of 5%~15% of the current value. After each adjustment, observe the product quality changes stably for at least 5~10 mold cycles, and continue adjusting only after confirming that the improvement direction is correct; one-step excessive adjustment must be avoided. 3. Increase the back pressure for venting. When implementing adjustments, it is recommended to adopt the single-factor variable method, adjusting only one parameter at a time and fully evaluating the effect, to avoid multiple parameters changing simultaneously making the cause of the problem untraceable. The adjustment magnitude should be small rather than large; each adjustment is recommended to be controlled within 5%~10% of the original value, and after adjustment, run stably for at least 3~5 mold cycles to observe the effect. In terms of material management, incoming inspection of raw materials and in-process inspection of work-in-progress should be strengthened, and the key performance indicators of PET, PP, HDPE, and PS should be strictly controlled to ensure the stability of molding quality from the source.

In summary, the causes of the "Bubble lines on the parison surface" problem can be attributed to the combined action of multiple factors such as volatile gases present in the raw material and injection speed too fast. Solving this problem requires starting from aspects such as fully dry the raw material and reduce the injection speed, and adopting systematic governance measures. In actual production, it is recommended to establish a prevention and rapid response mechanism for this problem, achieving stable production and continuous improvement through parison wall thickness uniformity and transfer temperature control.