Parison injection short shot (insufficient filling)

During the injection '2079851475616104457 production process, the product exhibits the quality defect of "Parison injection short shot (insufficient filling)". Specifically manifested as the parison not completely filling the mold cavity, with the end missing. This defect is relatively common when processing materials such as PET, PP, HDPE, and PS, and its occurrence conditions are usually related to unreasonable settings of injection pressure, parison temperature, blowing air pressure, and mold temperature. When the Parison injection short shot (insufficient filling) situation is severe, it will cause a series of chain-reaction quality defects in the product in terms of appearance, dimensional accuracy, mechanical properties, etc., which not only reduces the usability and safety of the product, but also directly increases the scrap rate and production cost. Therefore, this problem requires systematic diagnosis and optimization from multiple dimensions, including material selection, the condition of the injection '2079851475616104457 machine, core rod, parison mold, blow mold, and transfer mechanism, as well as injection pressure, parison temperature, blowing air pressure, and mold temperature.

1. Insufficient injection pressure. Pressure directly determines the filling ability of the melt and the mold-contacting effect during the '2079851475616104453. Insufficient pressure results in incomplete filling and poor replication accuracy; excessive pressure may cause secondary defects such as flash and excessive internal stress. The setting of pressure should comprehensively consider factors such as material viscosity, product dimensions, and mold structure. 2. Slow injection speed. Speed parameters affect the flow state and time allocation of the melt during the '2079851475616104453. A speed that is too slow leads to premature cooling and insufficient filling; a speed that is too fast causes melt fracture, air entrapment, and shear overheating. The optimization of the speed curve should make the melt flow smoothly and orderly in the cavity. 3. Melt temperature too low. Temperature is the core factor affecting melt fluidity and viscosity. Setting the temperature too high will cause the melt viscosity to decrease, insufficient melt strength, and even thermal degradation; if the temperature is too low, the melt fluidity is poor and plasticization is insufficient, making it impossible to fill or mold smoothly. A reasonable temperature window should be optimally determined within the recommended range according to the melting characteristics and thermal stability of the material. In terms of equipment maintenance, inadequate regular overhaul and accuracy confirmation of the injection '2079851475616104457 machine, core rod, parison mold, blow mold, and transfer mechanism cause the actual operating parameters of the equipment to deviate from the process requirements, which can also become a potential inducement of the Parison injection short shot (insufficient filling) problem.

1. Increase the injection pressure and speed. When implementing adjustments, it is recommended to adopt the single-factor variable method, adjusting only one parameter at a time and fully evaluating the effect, to avoid multiple parameters changing simultaneously making the cause of the problem untraceable. The adjustment magnitude should be small rather than large; each adjustment is recommended to be controlled within 5%~10% of the original value, and after adjustment, run stably for at least 3~5 mold cycles to observe the effect. 2. Appropriately increase the melt temperature. When implementing adjustments, it is recommended to adopt the single-factor variable method, adjusting only one parameter at a time and fully evaluating the effect, to avoid multiple parameters changing simultaneously making the cause of the problem untraceable. The adjustment magnitude should be small rather than large; each adjustment is recommended to be controlled within 5%~10% of the original value, and after adjustment, run stably for at least 3~5 mold cycles to observe the effect. It is recommended to formulate a preventive checklist for the Parison injection short shot (insufficient filling) problem, incorporate parison wall thickness uniformity and transfer temperature control into the scope of daily inspections, and conduct online monitoring of key parameters through the SPC statistical process control method to achieve early warning and rapid response to problems. In terms of material management, incoming inspection of raw materials and in-process inspection of work-in-progress should be strengthened, and the key performance indicators of PET, PP, HDPE, and PS should be strictly controlled to ensure the stability of molding quality from the source.

In summary, the causes of the "Parison injection short shot (insufficient filling)" problem can be attributed to the combined action of multiple factors such as insufficient injection pressure and slow injection speed. Solving this problem requires starting from aspects such as increase the injection pressure and speed and appropriately increase the melt temperature, and adopting systematic governance measures. In actual production, it is recommended to establish a prevention and rapid response mechanism for this problem, achieving stable production and continuous improvement through parison wall thickness uniformity and transfer temperature control.