Deformation of the product after high-temperature filling

In the extrusion '2079851475616104457 production process, the product exhibits the quality defect of "Deformation of the product after high-temperature filling".The specific manifestation is The bottle deforms after hot filling.This defect is more common when processing materials such as HDPE, PP, PVC and PC, and its occurrence is usually related to unreasonable settings of melt temperature, extrusion speed, blowing pressure and mold temperature.When the Deformation of the product after high-temperature filling situation is severe, it will cause a series of chain quality defects in the product's appearance, dimensional accuracy, mechanical properties and other aspects, which not only reduces the product's functionality and safety in use, but also directly increases the scrap rate and production cost.Therefore, this problem requires systematic diagnosis and optimization from multiple dimensions such as material selection, the status of the extruder, head, die, mold clamping mechanism and blowing system, and melt temperature, extrusion speed, blowing pressure and mold temperature.

1. Insufficient heat deflection temperature of the resin.Temperature is the core factor affecting melt fluidity and viscosity.Excessively high temperature settings will cause decreased melt viscosity, insufficient melt strength and even thermal degradation; excessively low temperature results in poor melt fluidity and insufficient plasticization, making smooth filling or forming impossible.A reasonable temperature window should be optimally determined within the recommended range according to the melting characteristics and thermal stability of the material. 2. Residual stress exists in the product.This factor causing the problem reflects that certain process conditions or material properties in extrusion '2079851475616104457 do not meet the optimal forming requirements.Such problems are often cumulative and concealed, and should be investigated and verified as key focus items during process debugging and finalization to ensure hidden dangers are eliminated at the source. In addition, the insufficient overall coordination of parison wall thickness control and parison temperature uniformity is also a factor that cannot be ignored; there are complex interactions and coupling relationships among the process parameters, and the deviation of any parameter may aggravate the degree of Deformation of the product after high-temperature filling through chain effects. In terms of equipment maintenance, the regular overhaul and accuracy confirmation of the extruder, head, die, mold clamping mechanism and blowing system are not in place, causing the actual operating parameters of the equipment to deviate from process requirements, which will also become a potential inducement of the Deformation of the product after high-temperature filling problem.

1. Select a heat-resistant resin grade.Before introducing new tools, new materials or new methods, sufficient applicability evaluation and small-batch verification should be carried out.It is recommended to first conduct offline tests or simulation analyses outside production conditions, and introduce them into the formal production line only after confirming effectiveness and safety.Keep proper change management records to facilitate subsequent traceability and experience accumulation. 2. Optimize the blow '2079851475616104453 to reduce residual stress.Adjustments should follow the principle of gradual progress; each adjustment should not be too large, and a decrement of 5%~15% of the current value is recommended.After each adjustment, stably observe the product quality changes for at least 5~10 mold cycles, and continue adjusting only after confirming the improvement direction is correct; never make excessive one-step adjustments. 3. Increase the wall thickness.When implementing adjustments, it is recommended to use the single-factor variable method, adjusting only one parameter at a time and fully evaluating the effect, to avoid simultaneous changes of multiple parameters making the cause of the problem untraceable.The adjustment amplitude should be small rather than large; each adjustment is recommended to be controlled within 5%~10% of the original value, and after adjustment run stably for at least 3~5 mold cycles to observe the effect. In terms of material management, incoming inspection of raw materials and in-process testing of work-in-progress should be strengthened, and key performance indicators of HDPE, PP, PVC and PC should be strictly controlled to ensure the stability of forming quality from the source.

In summary, the causes of the "Deformation of the product after high-temperature filling" problem can be attributed to the combined action of multiple factors such as Insufficient heat deflection temperature of the resin, Residual stress exists in the product.To solve this problem, it is necessary to start from aspects such as Select a heat-resistant resin grade, Optimize the blow '2079851475616104453 to reduce residual stress and take systematic governance measures.In actual production, it is recommended to establish a prevention and rapid response mechanism for this problem, achieving stable production and continuous improvement through parison wall thickness control and parison temperature uniformity.