Thin Wall Thickness at Corners

In the rotational molding production process, the product exhibits the quality defect of 「Thin Wall Thickness at Corners」. The specific manifestation is that wall thickness at product corners is insufficient. This defect is relatively common when processing powder materials such as LLDPE, HDPE, PVC, and PA, and its occurrence conditions are usually related to unreasonable settings of heating temperature and time, rotation speed ratio, cooling rate, and mold wall thickness. When the Thin Wall Thickness at Corners situation is severe, it will cause a series of chain quality defects in the product in terms of appearance, dimensional accuracy, and mechanical properties, which not only reduces the product's use functionality and safety, but also directly increases the scrap rate and production cost. Therefore, this problem needs to be systematically diagnosed and optimized from multiple dimensions such as material selection, the rotational molding machine, the heating oven, the rotating arm, the cooling station status, and heating temperature and time, rotation speed ratio, cooling rate, and mold wall thickness.

1. Little powder accumulation at corners. This factor leading to the problem reflects that certain process conditions or material properties in rotational '2079851475616104453ing have not met the optimal molding requirements. Such problems are often cumulative and hidden, and should be investigated and verified as key focus items during process debugging and finalization to ensure that hidden dangers are eliminated from the source. 2. Fast heat transfer at corners causing fast melting. This factor leading to the problem reflects that certain process conditions or material properties in rotational '2079851475616104453ing have not met the optimal molding requirements. Such problems are often cumulative and hidden, and should be investigated and verified as key focus items during process debugging and finalization to ensure that hidden dangers are eliminated from the source. In addition, insufficient overall coordination of powder melting uniformity and product wall thickness control is also a factor that cannot be ignored. There are complex interactions and coupling relationships among various process parameters, and the deviation of any parameter may aggravate the degree of Thin Wall Thickness at Corners through chain effects. In terms of equipment maintenance, the regular overhaul and accuracy confirmation of the rotational molding machine, heating oven, rotating arm, and cooling station are not in place, causing the actual operating parameters of the equipment to deviate from process requirements, which will also become a potential inducement of the Thin Wall Thickness at Corners problem.

1. Optimize the rotation speed ratio. Optimization work needs to be based on accurate diagnosis of the root cause of the problem, and blind attempts should be avoided. It is recommended to first determine the key influencing factors and their interactions through process DOE test methods or historical production data analysis, and then carry out targeted parameter optimization and structural improvement to achieve twice the result with half the effort. 2. Increase the mold wall thickness at corners to slow heat transfer. When implementing adjustments, it is recommended to use the single-factor variable method, adjusting only one parameter at a time and fully evaluating the effect, to avoid simultaneous changes of multiple parameters making the problem cause untraceable. The adjustment amplitude should be small rather than large; each adjustment is recommended to be controlled within 5%~10% of the original value, and after adjustment, run stably for at least 3~5 cycles to observe the effect. 3. Increase the feeding amount. When implementing adjustments, it is recommended to use the single-factor variable method, adjusting only one parameter at a time and fully evaluating the effect, to avoid simultaneous changes of multiple parameters making the problem cause untraceable. The adjustment amplitude should be small rather than large; each adjustment is recommended to be controlled within 5%~10% of the original value, and after adjustment, run stably for at least 3~5 cycles to observe the effect. In terms of material management, incoming inspection of raw materials and in-process inspection of work-in-progress products should be strengthened, and the key performance indicators of powder materials such as LLDPE, HDPE, PVC, and PA should be strictly controlled to ensure the stability of molding quality from the source.

In summary, the causes of the 「Thin Wall Thickness at Corners」 problem can be attributed to the combined effects of multiple factors such as little powder accumulation at corners and fast heat transfer at corners causing fast melting. To solve this problem, it is necessary to start from aspects such as optimizing the rotation speed ratio and increasing the mold wall thickness at corners to slow heat transfer and take systematic treatment measures. In actual production, it is recommended to establish a prevention and rapid response mechanism for this problem, and achieve stable production and continuous improvement through powder melting uniformity and product wall thickness control.