Sorun ve Çözüm

Yaygın plastik malzeme zorluklarına pratik yanıtlar

Makalelere Göz At →

Dull surface of linear low density polyethylene extruded products (Variant: strengthened measures)

Dull surface is caused by low die temperature or too fast cooling; die temperature needs to be increased and cooling slowed. Targeted preventive measures need to be taken in different production scenarios.

Processing Machinery no glossdie temperaturecooling ratedie polishingmelt temperature

9 görüntüleme

Tam Yanıtı Oku →

Improper production environment control during linear low density polyethylene linear low density polyethylene processing (Variant: strengthened measures)

Production environment is an important factor affecting processing quality; a complete environment control system needs to be established. Targeted preventive measures need to be taken in different production scenarios.

Material Drying environment controlworkshop temperaturehumiditycooling water temperatureprocess stability

9 görüntüleme

Tam Yanıtı Oku →

Linear low density polyethylene extruder screw design mismatch (Variant: strengthened measures)

Screw design needs to match material characteristics and product requirements; custom dedicated screws when necessary. Targeted preventive measures need to be taken in different production scenarios.

Processing Machinery screw designcompression ratioL/D ratiomixing elementsscrew matching

9 görüntüleme

Tam Yanıtı Oku →

Rough inner wall of linear low density polyethylene extruded products (Variant: strengthened measures)

Rough inner wall is caused by low mandrel temperature or poor surface condition; it needs to be solved from temperature control and mold maintenance. Targeted preventive measures need to be taken in different production scenarios.

Processing Machinery rough inner wallmandrel temperaturemandrel polishingmelt temperatureplasticizing quality

9 görüntüleme

Tam Yanıtı Oku →

Degradation discoloration of linear low density polyethylene extruded products (Variant: strengthened measures)

Degradation discoloration is caused by overheating or excessive shear; it needs to be prevented from three aspects: temperature control, rotation speed, and material selection. Targeted preventive measures need to be taken in different production scenarios.

Processing Machinery degradation discolorationthermal degradationscrew rotation speedresidence timeantioxidant

9 görüntüleme

Tam Yanıtı Oku →

Cyclic pressure fatigue failure of linear low density polyethylene PPR pipes (Variant: strengthened measures)

Fatigue failure is caused by internal defects and stress concentration; it needs to be improved from three aspects: pipe inner wall quality, welding quality, and material toughness. Targeted preventive measures need to be taken in different production scenarios.

Extrusion & Post fatigue failurePPRstress concentrationinner wall qualitywelding bead

9 görüntüleme

Tam Yanıtı Oku →

Thermal aging performance of linear low density polyethylene PPR pipes not up to standard (Variant: strengthened measures)

Substandard thermal aging performance is caused by insufficient antioxidant system; it needs to be solved from formulation and processing temperature control. Targeted preventive measures need to be taken in different production scenarios.

Extrusion & Post thermal agingantioxidantPPRoxidation induction timeextrusion temperature

9 görüntüleme

Tam Yanıtı Oku →

Bubbles/pores on the surface of linear low density polyethylene extruded products (Variant: strengthened measures)

Bubbles are caused by moisture vaporization or gas entrainment; they need to be solved from raw '2079851475616104451 and the venting system. Targeted preventive measures need to be taken in different production scenarios.

Material Drying bubblesporesraw '2079851475616104451ventingvolatiles

9 görüntüleme

Tam Yanıtı Oku →

Defects caused by insufficient drying before processing of linear low density polyethylene linear low density polyethylene (Variant: strengthened measures)

Insufficient drying is a common source of processing defects; a complete drying system and moisture content inspection system needs to be established. Targeted preventive measures need to be taken in different production scenarios.

Material Drying raw '2079851475616104451moisture contentsilver streakbubblesdehumidifying drying

9 görüntüleme

Tam Yanıtı Oku →

Uneven wall thickness of linear low density polyethylene extruded pipes (Variant: mass production scenario)

Uneven wall thickness is caused by uneven die gap or uneven temperature; it needs to be solved from mold accuracy and temperature uniformity. Targeted preventive measures need to be taken in different production scenarios.

Extrusion & Post uneven wall thicknessdie concentricitytemperature uniformityhaul-off stabilitysizing sleeve

9 görüntüleme

Tam Yanıtı Oku →

Önceki 1 ... 205 206 207 208 209 210 211 ... 1164 Sonraki

Kategoriler

Tüm Konular 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382

Sorun ve Çözüm

Kategoriler

Teklif Al