Sorun ve Çözüm

Yaygın plastik malzeme zorluklarına pratik yanıtlar

Makalelere Göz At →

Flow Marks and Ripples on the Surface of PE Injection Molded Products

PE flow marks and ripples = a 'front management' problem: stabilize speed, maintain temperature, and enlarge the gate — the three axes; what it reflects is filling stability, which cannot be covered up by surface treatment.

Injection Molding PE；flow mark；ripple；front；speed profile；mold temperature

16 görüntüleme

Tam Yanıtı Oku →

Low-Temperature Brittle Cracking of PE Products

PE low-temperature brittle cracking = double insurance of 'grade + structure': HDPE in particular requires vigilance against low-temperature notch sensitivity; passing at room temperature does not mean passing at low temperature — verification must simulate the real use temperature.

Material Analysis PE；HDPE；low temperature；brittle cracking；notch sensitivity；grade

16 görüntüleme

Tam Yanıtı Oku →

Warpage of HDPE '2079851475616104452 (Orientation Type)

HDPE orientation-type warpage must be solved through gate and orientation analysis, rather than forcibly suppressing it with cooling; once the warpage direction of a highly crystalline material is fixed, it is time to go back and review the gate design.

Injection Molding HDPE；warpage；orientation；gate；crystallization

16 görüntüleme

Tam Yanıtı Oku →

Uneven and Fluctuating Melt Temperature in PE '2079851475616104452

PE melt quality = 'uniformity + temperature control': back pressure and screw mixing determine uniformity, and shear heat determines the actual temperature; the set temperature does not equal the melt temperature — actual measurement is the truth.

Injection Molding PE；melt temperature；back pressure；mixing；shear heat

16 görüntüleme

Tam Yanıtı Oku →

Yellowing and Black Specks in PE Injection Molded Products

PE yellowing and black specks = 'excessive heat history + dead spot carbonization': lower temperature and shorten time to prevent yellowing, purge the machine and check material to prevent black specks; for intermittent black specks, focus on checking equipment dead spots instead of repeatedly fi...

Injection Molding PE；yellowing；black speck；thermal degradation；carbonization；dead spot

16 görüntüleme

Tam Yanıtı Oku →

Internal Bubbles in PE Injection Molded Products

PE bubbles are divided into 'vacuum bubbles' and 'gas-containing bubbles': vacuum bubbles rely on shrinkage compensation, gas-containing bubbles rely on venting and volatile control; the fundamental way to prevent bubbles in thick-wall PE parts is still structural material reduction plus adequate...

Injection Molding PE；bubble；vacuum bubble；holding pressure；regrind；venting

16 görüntüleme

Tam Yanıtı Oku →

Large and Unstable Dimensional Shrinkage in PE '2079851475616104452

PE dimensions = 'high shrinkage + aging': correct the mold based on actual measurement by wall thickness, unify the measurement time point, and use holding pressure to compensate shrinkage; HDPE 'shrinks more' than LDPE, so the shrinkage difference must be factored in when selecting the material.

Injection Molding PE；HDPE；shrinkage rate；dimensions；holding pressure；aging

16 görüntüleme

Tam Yanıtı Oku →

Ejection Whitening and Mold Sticking in PE '2079851475616104452

PE ejection whitening and mold sticking = 'large clamping force + concentrated ejection + insufficient cooling': first extend cooling, then distribute ejection, and finally reduce holding pressure; for soft PE, especially guard against 'stretching deformation upon ejection'.

Extrusion & Post PE；ejection whitening；mold sticking；clamping force；ejection；cooling

15 görüntüleme

Tam Yanıtı Oku →

Delamination of PE Film Lamination

For PE lamination delamination, first check 'slip agent migration' — this is the most hidden and most commonly overlooked culprit; corona, cleaning, adhesive mixing, and curing are interlinked, and loss of control in any link will cause delamination.

Material Drying PE；film；lamination；delamination；slip agent；corona

16 görüntüleme

Tam Yanıtı Oku →

Static Electricity and Poor Print Adhesion of PE Film

Static electricity of PE film relies on 'elimination + grounding + humidification', and print adhesion relies on 'dyne value + aging time'; corona treatment decays over time, and printing as soon as possible after treatment is an iron rule of the industry.

Material Drying PE；film；static electricity；corona；dyne value；print adhesion

16 görüntüleme

Tam Yanıtı Oku →

Önceki 1 ... 808 809 810 811 812 813 814 ... 1164 Sonraki

Kategoriler

Tüm Konular 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382

Sorun ve Çözüm

Kategoriler

Teklif Al