Low mold cooling efficiency

During the extrusion '2079851475616104457 production process, the product exhibits the quality defect of "Low mold cooling efficiency". Specifically manifested as long cooling time and low production efficiency. This defect is relatively common when processing materials such as HDPE, PP, PVC, and PC, and its occurrence conditions are usually related to unreasonable settings of melt temperature, extrusion speed, blowing air pressure, and mold temperature. When the Low mold cooling efficiency situation is severe, it will cause a series of chain-reaction quality defects in the product in terms of appearance, dimensional accuracy, mechanical properties, etc., which not only reduces the usability and safety of the product, but also directly increases the scrap rate and production cost. Therefore, this problem requires systematic diagnosis and optimization from multiple dimensions, including material selection, the condition of the extruder, die head, die, mold clamping mechanism, and blowing system, as well as melt temperature, extrusion speed, blowing air pressure, and mold temperature.

1. Unreasonable cooling water channel design. Cooling conditions determine the setting process and the final internal structure of the product. Uneven cooling leads to shrinkage differences and residual stress, causing warpage and dimensional deviations; insufficient cooling makes the product not rigid enough at demolding; excessively rapid cooling generates large internal stress. The cooling system design should ensure uniform and efficient heat dissipation in all areas. 2. Insufficient water flow. This factor leading to the problem reflects that certain process conditions or material properties in extrusion blow '2079851475616104453ing have not met the optimal molding requirements. Such problems often have cumulative and hidden characteristics, and should be investigated and verified as key focus items during process debugging and finalization to ensure that hidden dangers are eliminated from the source. 3. Poor thermal conductivity of the mold material. The mold is the core tool that imparts shape and surface quality to the product. Unreasonable mold design, such as improper runner/gate dimensions, insufficient venting, inadequate draft angle, etc., will directly cause molding defects. The machining accuracy, surface treatment quality, and daily maintenance condition of the mold also directly affect product quality. In terms of equipment maintenance, inadequate regular overhaul and accuracy confirmation of the extruder, die head, die, mold clamping mechanism, and blowing system cause the actual operating parameters of the equipment to deviate from the process requirements, which can also become a potential inducement of the Low mold cooling efficiency problem.

1. Optimize the cooling water channel layout. Optimization work must be based on an accurate diagnosis of the root cause of the problem, and blind attempts must be avoided. It is recommended to first determine the key influencing factors and their interactions through the process DOE test method or historical production data analysis, and then carry out targeted parameter optimization and structural improvement to achieve twice the result with half the effort. 2. Increase the water flow. When implementing adjustments, it is recommended to adopt the single-factor variable method, adjusting only one parameter at a time and fully evaluating the effect, to avoid multiple parameters changing simultaneously making the cause of the problem untraceable. The adjustment magnitude should be small rather than large; each adjustment is recommended to be controlled within 5%~10% of the original value, and after adjustment, run stably for at least 3~5 mold cycles to observe the effect. 3. Select inserts of high thermal conductivity materials such as beryllium copper alloy. Before introducing new tools, new materials, or new methods, a full applicability assessment and small-batch verification should be carried out. It is recommended to first conduct offline tests or simulation analysis outside of production conditions, and introduce them into the formal production line only after confirming effectiveness and safety. Keep change management records to facilitate subsequent traceability and experience accumulation. In terms of material management, incoming inspection of raw materials and in-process inspection of work-in-progress should be strengthened, and the key performance indicators of HDPE, PP, PVC, and PC should be strictly controlled to ensure the stability of molding quality from the source.

In summary, the causes of the "Low mold cooling efficiency" problem can be attributed to the combined action of multiple factors such as unreasonable cooling water channel design and insufficient water flow. Solving this problem requires starting from aspects such as optimize the cooling water channel layout and increase the water flow, and adopting systematic governance measures. In actual production, it is recommended to establish a prevention and rapid response mechanism for this problem, achieving stable production and continuous improvement through parison wall thickness control and parison temperature uniformity.