Product side wall too thin

In the '2079851475616104458 (vacuum forming) production process, the product exhibits the quality defect of "Product side wall too thin". The specific manifestation is that the wall thickness of the product side wall is too thin. This defect is relatively common when processing materials such as PP, PS, PET, PVC, ABS sheets, and its occurrence conditions are usually related to the unreasonable settings of sheet heating temperature, forming pressure/vacuum level, mold temperature, and cooling time. When the "Product side wall too thin" situation is severe, it will cause a series of chain quality defects in the product in terms of appearance, dimensional accuracy, mechanical properties, etc., which not only reduces the functionality and safety of the product in use, but also directly increases the scrap rate and production cost. Therefore, this problem requires systematic diagnosis and optimization from multiple dimensions such as material selection, the status of the '2079851475616104458 machine, heating oven, mold, and vacuum/air pressure system, and sheet heating temperature, forming pressure/vacuum level, mold temperature, and cooling time.

1. Large stretch ratio at the side wall. This factor causing the problem reflects that certain process conditions or material characteristics in '2079851475616104458 (vacuum forming) processing have not met the optimal molding requirements. Such problems are often cumulative and hidden, and should be investigated and verified as key focus items during process debugging and finalization to ensure that hidden dangers are eliminated at the source. 2. Uneven sheet temperature. Temperature is the core factor affecting melt fluidity and viscosity. A temperature set too high will cause the melt viscosity to decrease, insufficient melt strength, and even thermal degradation; a temperature that is too low results in poor melt fluidity and insufficient plasticization, making it impossible to fill or form smoothly. A reasonable temperature window should be optimized and determined within the recommended range according to the melting characteristics and thermal stability of the material. 3. Forming speed too fast. The speed parameter affects the flow state and time allocation of the melt during the forming process. A speed that is too slow causes premature cooling and insufficient filling; a speed that is too fast causes melt fracture, air entrapment, and shear overheating. The optimization of the speed curve should make the melt flow smoothly and orderly in the cavity. In terms of equipment maintenance, the regular overhaul and precision confirmation of the '2079851475616104458 machine, heating oven, mold, and vacuum/air pressure system are not in place, causing the actual operating parameters of the equipment to deviate from the process requirements, which will also become a potential inducement of the "Product side wall too thin" problem.

1. Use plug pre-stretching. Before introducing new tools, new materials, or new methods, a full applicability assessment and small-batch verification should be carried out. It is recommended to first conduct offline tests or simulation analysis outside production conditions, and introduce them into the formal production line only after confirming effectiveness and safety. Keep change management records to facilitate subsequent traceability and experience accumulation. 2. Optimize the heating uniformity. Optimization work must be based on an accurate diagnosis of the root cause of the problem, and blind attempts must be avoided. It is recommended to first determine the key influencing factors and their interactions through the process DOE test method or historical production data analysis, and then carry out parameter optimization and structural improvement in a targeted manner to achieve twice the result with half the effort. 3. Reduce the forming speed. Before implementing this measure, its feasibility and expected effect should be fully evaluated, and the details of the plan should be communicated and confirmed with relevant technical personnel; during implementation, closely monitor changes in key quality indicators, promptly record and feedback the adjustment effect, and form reusable process experience. In terms of material management, incoming inspection of raw materials upon arrival and in-process inspection of work-in-progress should be strengthened, and the key performance indicators of PP, PS, PET, PVC, ABS sheets should be strictly controlled to ensure the stability of molding quality from the source.

In summary, the causes of the "Product side wall too thin" problem can be attributed to the combined action of multiple factors such as Large stretch ratio at the side wall, Uneven sheet temperature. Solving this problem requires starting from aspects such as Use plug pre-stretching, Optimize the heating uniformity and adopting systematic governance measures. In actual production, it is recommended to establish a prevention and rapid response mechanism for this problem, and achieve stable production and continuous improvement through sheet heating uniformity and stretch ratio control.