문제 및 해결책

일반적인 플라스틱 재료 문제에 대한 실질적인 답변

기사 둘러보기 →

Q

LDPE Temperature Lower Limit

A

The LDPE temperature lower limit ensures sufficient plasticizing; After confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; Incorporate this case into the defect archive as a troubleshooting reference for similar future problems.

Processing Machinery LDPEtemperature lower limitplasticizinggel particle

Q

LDPE Melt Temperature Range

A

LDPE melt upper limit is 240℃; over-temperature causes oxidation; After confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; Incorporate this case into the defect archive as a troubleshooting reference for similar future problems.

Processing Machinery LDPEmelt temperatureoxidationyellow spot

Q

LDPE Drying Judgment

A

LDPE drying is performed as needed; bubbles are not necessarily attributed to moisture; After confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; Incorporate this case into the defect archive as a troubleshooting reference for similar f...

Material Drying LDPEdryingbubbleattached water

Q

LDPE Processing Temperature Upper Limit

A

LDPE's temperature upper limit also exists; the 280℃ red line plus residence management prevents oxidative degradation; After confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Material Analysis LDPE; temperature upper limit; 280℃; thermal oxidation; degradation

Q

LDPE Screw Versatility

A

LDPE is the friendliest to equipment; general configuration suffices, upgrade to a barrier screw for high requirements; After confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Processing Machinery LDPE; screw; barrier type; back pressure; plasticizing

Q

LDPE Air Ring Single and Dual Lips

A

Air ring selection upgrades with the material; single lip is enough for LDPE, LLDPE must have dual lips plus internal cooling; After confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Extrusion & Post LDPE; air ring; single lip; dual lip; bubble stability

Q

LDPE Die Gap Comparison

A

The die gap is the equipment watershed between LDPE and LLDPE; the 2-3 times difference must be reflected in the material change procedure; After confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Blow Molding LDPE; LLDPE; die gap; back pressure; material change

Q

LDPE Blown Film Frost Line Management

A

The frost line is the steering wheel of the blown film process; the balance between bubble stability and film transparency is all adjusted by it; After confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Extrusion & Post LDPE; blown film; frost line; air ring; IBC

Q

LDPE Mold Temperature 20-60℃

A

LDPE mold temperature adjustment requires patience; 10℃ steps plus 10-cycle stabilization is the standard rhythm to avoid misjudgment; After confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling LDPE; mold temperature; 20-60℃; 10 cycles; stabilization

Q

LDPE Shrinkage Dominated by Cooling Time

A

The correct order for LDPE shrinkage management is cooling, holding, injection; design of experiments data overturns the priority of experience-based machine tuning; After confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Injection Molding LDPE; shrinkage; cooling time; Taguchi; holding pressure

이전 1 ... 946 947 948 949 950 951 952 ... 1164 다음

카테고리

전체 주제 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382