문제 및 해결책

일반적인 플라스틱 재료 문제에 대한 실질적인 답변

기사 둘러보기 →

Q

Risk of Laxity in LCP Moisture Management

A

Low moisture absorption is an advantage of LCP, not an excuse to skip drying; trace moisture still causes blistering; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Material Drying moisture management drying silver streak hydrolysis

Q

Selection Confusion Between LCP and High-Temperature Materials Such as PPS/PEEK

A

For high-temperature material selection, first define core requirements; LCP's irreplaceability lies in ultra-thin-wall flow; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling material selection PPS PEEK PA9T

Q

Cracking of LCP Products in Post-Processing and Secondary Assembly

A

LCP post-processing fears transverse tearing; tool feed and interference are verified according to the weak direction; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Extrusion & Post post-processing cracking assembly interference orientation direction

Q

LCP Injection Cycle Optimization and Rapid Crystallization Utilization

A

LCP's fast crystallization is a capacity dividend; cooling time should be stepped down and verified level by level; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting r...

Injection Molding molding cycle rapid crystallization cooling time capacity

Q

Sharkskin on LCP Extruded Profile Surface

A

Sharkskin is a signal of shear exceeding the critical value; lowering temperature and raising speed is not as good as matching speed increase with temperature decrease; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include t...

Extrusion & Post extrusion sharkskin melt fracture die

Q

Wrong Selection Among Three Melting-Point Classes of LCP Grades

A

LCP temperature is set by class; when changing grades, the melting point must be checked before setting the process; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting ...

Molding Process grade classification melting point temperature setting class I class II class III

Q

Dielectric Advantages and Molding Requirements of LCP in 5G High-Frequency Applications

A

LCP for 5G wins on dielectric; batch consistency relies on process locking and SPC; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molding Process 5G dielectric loss high frequency consistency

Q

Utilization of LCP Orientation-Direction Mechanical Property Differences

A

LCP performance data must carry direction; design verification uses the conservative transverse value; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for ...

Material Analysis orientation mechanical properties directionality test sampling

Q

LCP Hot Runner System Adaptation Problems

A

The success or failure of LCP hot runners lies in temperature control precision; both carbonization and stringing originate from temperature loss of control; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling hot runner temperature control precision stringing carbonization

Q

Control of LCP Regrind Usage Ratio

A

LCP regrind must be re-dried and its ratio limited; soldered parts require strict verification; after confirming effectiveness, solidify the parameters and practices into the work instruction to prevent recurrence; include this case in the defect archive as a troubleshooting reference for subsequ...

Material Drying regrind thermal history blistering rate ratio control

이전 1 ... 958 959 960 961 962 963 964 ... 1164 다음

카테고리

전체 주제 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382