المشاكل والحلول

إجابات عملية على التحديات الشائعة في مواد البلاستيك

تصفح المقالات →

Q

PVC Injection Product Dull Surface

A

PVC gloss = 'plasticization + mold temperature + anti-degradation': degradation dragging gloss dark is PVC's characteristic; plasticization and mold temperature manage replication, anti-degradation manages base color; after confirming effectiveness, fix the parameters and practices into the work ...

Injection Molding PVC; '2079851475616104452; gloss; plasticization; mold temperature

Q

PVC Injection Hot Runner Problems

A

PVC + hot runner = 'high-precision temperature control challenge': dead corners and temperature control deviation are the two minefields; PVC with hot runner has extremely high system precision requirements, needs dedicated design and maintenance.

Injection Molding PVC; hot runner; black speck; temperature control; retention

Q

PVC Injection Product Dimension Instability

A

PVC dimension = 'plasticization and metering stability': plasticization fluctuation is PVC's characteristic root of dimension instability; stabilize plasticization and metering, dimensions are then guaranteed; after confirming effectiveness, fix the parameters and practices into the work instruct...

Injection Molding PVC; '2079851475616104452; dimension; plasticization; cushion

Q

PVC Injection Mold Sticking

A

PVC mold sticking = 'pressure + draft + degradation': degraded material being stickier is PVC's characteristic; besides reducing pressure and temperature, anti-degradation and polishing are equally important; after confirming effectiveness, fix the parameters and practices into the work instructi...

Injection Molding PVC; '2079851475616104452; mold sticking; holding pressure; degradation

Q

PVC Injection Weak Weld Line

A

PVC weld line = 'temperature + venting + anti-degradation': PVC melt has high elasticity and converges with difficulty, temperature and venting must be given sufficiently, and more importantly prevent degraded flow front from making the weld line brittle.

Injection Molding PVC; '2079851475616104452; weld line; venting; degradation

Q

PVC Injection Flash

A

PVC flash 'also beware of degradation-induced viscosity drop': degradation makes PVC suddenly thin and flash; besides reducing pressure and increasing clamping, check back whether thermal degradation caused abnormal viscosity.

Injection Molding PVC; '2079851475616104452; flash; clamping; degradation

Q

PVC Injection Short Shot

A

PVC short shot = 'the pressure-temperature account of high viscosity': raise temperature and pressure within the safe window; PVC is heat-sensitive, heating must be cautious — large gates and venting are often safer and more effective than forced heating.

Injection Molding PVC; '2079851475616104452; short shot; viscosity; pressure

Q

PVC Injection Products Brittle

A

PVC brittleness 'check both ends': both insufficient plasticization and degradation cause brittleness, opposite directions must be distinguished; use immersion method and appearance features to distinguish, then treat accordingly — insufficient plasticization: raise temperature and add shear; deg...

Injection Molding PVC; '2079851475616104452; brittleness; plasticization; degradation

Q

PVC Injection Flow Marks

A

PVC flow marks = a 'plasticization uniformity' problem: uneven plasticization is the root; PVC melt has high elasticity, any slight flow instability leaves marks on the surface — uniformity of plasticization and temperature control is fundamental.

Injection Molding PVC; '2079851475616104452; flow mark; plasticization; melt temperature

Q

PVC Injection Burnt (Gate Burnt Marks)

A

PVC injection burnt = 'shear heat exceeding limit': the gate is the key protection area; PVC is a heat-sensitive material, gate shear heat is most likely to 'burn' it — large gate + low temperature + slow speed is the basic setup.

Injection Molding PVC; '2079851475616104452; burnt; gate; shear heat

السابق 1 ... 98 99 100 101 102 103 104 ... 151 التالي

الفئات

جميع المواضيع 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382