Poor mold venting

In the stretch '2079851475616104457 production process, the product exhibits the quality defect of "Poor mold venting". The specific manifestation is that air in the blow mold cavity cannot be discharged, resulting in incomplete filling. This defect is relatively common when processing materials such as PET, PP, PC, and its occurrence conditions are usually related to the unreasonable settings of stretching temperature, stretch ratio, blowing pressure, and preform heating uniformity. When the "Poor mold venting" situation is severe, it will cause a series of chain quality defects in the product in terms of appearance, dimensional accuracy, mechanical properties, etc., which not only reduces the functionality and safety of the product in use, but also directly increases the scrap rate and production cost. Therefore, this problem requires systematic diagnosis and optimization from multiple dimensions such as material selection, the status of the stretch '2079851475616104457 machine, heating oven, stretch rod, and blow mold, and stretching temperature, stretch ratio, blowing pressure, and preform heating uniformity.

1. Vent holes or vent grooves clogged. Mold venting is a basic condition for ensuring smooth filling of the melt. When venting is poor, the air in the mold cavity is compressed to form a high-pressure air cushion, which hinders melt flow and causes problems such as insufficient filling, burning, and weld lines. A reasonable venting design should consider the venting positions and venting gaps to ensure that air is discharged in time. 2. Insufficient venting structure design. Mold venting is a basic condition for ensuring smooth filling of the melt. When venting is poor, the air in the mold cavity is compressed to form a high-pressure air cushion, which hinders melt flow and causes problems such as insufficient filling, burning, and weld lines. A reasonable venting design should consider the venting positions and venting gaps to ensure that air is discharged in time. In addition, the insufficient overall coordination of preform heating uniformity and biaxial stretch orientation control is also a factor that cannot be ignored; there are complex interactions and coupling relationships among the process parameters, and the deviation of any one parameter may aggravate the degree of "Poor mold venting" through chain effects. In terms of equipment maintenance, the regular overhaul and precision confirmation of the stretch '2079851475616104457 machine, heating oven, stretch rod, and blow mold are not in place, causing the actual operating parameters of the equipment to deviate from the process requirements, which will also become a potential inducement of the "Poor mold venting" problem.

1. Clean the vent holes. Cleaning work should be incorporated into the equipment preventive maintenance plan, and the cleaning frequency should be reasonably determined according to the actual conditions of the processing materials and operating cycle. Use dedicated cleaning tools and cleaning materials to avoid scratching the cavity surface or electrolytic corrosion caused by improper operation. After cleaning, recheck and confirm that the key clearances are accurate. 2. Add vent grooves. The installation of equipment or accessories should strictly follow the installation instructions; key mating surfaces must be cleaned and checked for damage before installation. Fastening bolts should be tightened evenly according to the specified torque value and diagonal sequence; after installation, use precision measuring tools to check whether the installation accuracy meets the technical requirements. 3. Use porous metal inserts. Before introducing new tools, new materials, or new methods, a full applicability assessment and small-batch verification should be carried out. It is recommended to first conduct offline tests or simulation analysis outside production conditions, and introduce them into the formal production line only after confirming effectiveness and safety. Keep change management records to facilitate subsequent traceability and experience accumulation. In terms of material management, incoming inspection of raw materials upon arrival and in-process inspection of work-in-progress should be strengthened, and the key performance indicators of PET, PP, PC should be strictly controlled to ensure the stability of molding quality from the source.

In summary, the causes of the "Poor mold venting" problem can be attributed to the combined action of multiple factors such as Vent holes or vent grooves clogged, Insufficient venting structure design. Solving this problem requires starting from aspects such as Clean the vent holes, Add vent grooves and adopting systematic governance measures. In actual production, it is recommended to establish a prevention and rapid response mechanism for this problem, and achieve stable production and continuous improvement through preform heating uniformity and biaxial stretch orientation control.