Intermittent pauses during parison extrusion

In the extrusion '2079851475616104457 production process, the product exhibits the quality defect of "Intermittent pauses during parison extrusion".The specific manifestation is The parison extrusion pauses intermittently and discontinuously.This defect is more common when processing materials such as HDPE, PP, PVC and PC, and its occurrence is usually related to unreasonable settings of melt temperature, extrusion speed, blowing pressure and mold temperature.When the Intermittent pauses during parison extrusion situation is severe, it will cause a series of chain quality defects in the product's appearance, dimensional accuracy, mechanical properties and other aspects, which not only reduces the product's functionality and safety in use, but also directly increases the scrap rate and production cost.Therefore, this problem requires systematic diagnosis and optimization from multiple dimensions such as material selection, the status of the extruder, head, die, mold clamping mechanism and blowing system, and melt temperature, extrusion speed, blowing pressure and mold temperature.

1. Bridging in the feeding system.This factor causing the problem reflects that certain process conditions or material properties in extrusion '2079851475616104457 do not meet the optimal forming requirements.Such problems are often cumulative and concealed, and should be investigated and verified as key focus items during process debugging and finalization to ensure hidden dangers are eliminated at the source. 2. Slipping in the screw feeding section.This factor causing the problem reflects that certain process conditions or material properties in extrusion '2079851475616104457 do not meet the optimal forming requirements.Such problems are often cumulative and concealed, and should be investigated and verified as key focus items during process debugging and finalization to ensure hidden dangers are eliminated at the source. In addition, the insufficient overall coordination of parison wall thickness control and parison temperature uniformity is also a factor that cannot be ignored; there are complex interactions and coupling relationships among the process parameters, and the deviation of any parameter may aggravate the degree of Intermittent pauses during parison extrusion through chain effects. In terms of equipment maintenance, the regular overhaul and accuracy confirmation of the extruder, head, die, mold clamping mechanism and blowing system are not in place, causing the actual operating parameters of the equipment to deviate from process requirements, which will also become a potential inducement of the Intermittent pauses during parison extrusion problem.

1. Install an agitator or vibrator on the hopper.Installation of equipment or accessories should strictly follow the installation manual; key mating surfaces must be cleaned and checked for damage before installation.Fastening bolts should be tightened evenly according to the specified torque values and diagonal sequence; after installation, use precision measuring tools to verify whether the installation accuracy meets technical requirements. 2. Lower the first zone temperature to prevent material sticking.Adjustments should follow the principle of gradual progress; each adjustment should not be too large, and a decrement of 5%~15% of the current value is recommended.After each adjustment, stably observe the product quality changes for at least 5~10 mold cycles, and continue adjusting only after confirming the improvement direction is correct; never make excessive one-step adjustments. It is recommended to formulate a preventive checklist for the Intermittent pauses during parison extrusion problem, incorporate parison wall thickness control and parison temperature uniformity into the daily inspection scope, and conduct online monitoring of key parameters through the SPC statistical process control method to achieve early warning and rapid response to problems. In terms of material management, incoming inspection of raw materials and in-process testing of work-in-progress should be strengthened, and key performance indicators of HDPE, PP, PVC and PC should be strictly controlled to ensure the stability of forming quality from the source.

In summary, the causes of the "Intermittent pauses during parison extrusion" problem can be attributed to the combined action of multiple factors such as Bridging in the feeding system, Slipping in the screw feeding section.To solve this problem, it is necessary to start from aspects such as Install an agitator or vibrator on the hopper, Lower the first zone temperature to prevent material sticking and take systematic governance measures.In actual production, it is recommended to establish a prevention and rapid response mechanism for this problem, achieving stable production and continuous improvement through parison wall thickness control and parison temperature uniformity.