문제 및 해결책

일반적인 플라스틱 재료 문제에 대한 실질적인 답변

기사 둘러보기 →

Q

White Stress Marks on PEEK Surface

A

PEEK stress whitening is a direct signal of local overload; check both the de'2079851475616104453 and the crystallization state; white-marked areas should be evaluated as key strength weak points.

Molds & Tooling PEEK；stress whitening；ejection whitening；crystallization；demolding；overload

Q

Much Setup Scrap for PEEK First Articles

A

PEEK setup cost must be hedged with data-based management; process cards and simulation analysis are the core tools for reducing trial and error; every kilogram of scrap is a loss of real money.

Molds & Tooling PEEK；setup；scrap；process card；simulation；cost

Q

Excessive Post-Shrinkage of PEEK Products

A

The root of PEEK post-shrinkage is still crystallinity management; completing crystallization properly during molding is the most thorough solution; high-temperature applications must undergo aging dimensional verification before finalizing the design.

Molds & Tooling PEEK；post-shrinkage；secondary crystallization；aging；dimensions；setting

Q

Poor Insert Bonding of PEEK

A

The core contradiction of PEEK insert parts is thermal expansion mismatch; preheating and mechanical interlock are the two basic means; interface verification must include temperature cycling conditions.; After confirming effectiveness, solidify the parameters and practices into the work instruct...

Molding Process PEEK；insert；interface；thermal expansion；preheating；interlock

Q

Insufficient '2079851475616104452 Machine Selection for PEEK

A

PEEK's hard requirements for equipment cannot be compensated by process techniques; equipment selection mistakes are congenital defects; investing in high-temperature dedicated equipment is a prerequisite for PEEK projects.

Injection Molding PEEK；'2079851475616104452 machine；selection；high temperature；temperature control；screw

Q

Thermal Expansion Out of Control of PEEK High-Temperature Molds

A

PEEK mold design must consider the thermal expansion at 200℃-level working temperatures; room-temperature fitting data cannot be directly applied; the maintenance cost of high-temperature molds should be included in the project budget.

Molds & Tooling PEEK；mold；thermal expansion；high temperature；seizure；wear

Q

Degradation from Blending Recycled Material into PEEK

A

The core of PEEK recycled material management is controlling the number of heat histories; melt index testing is a practical means to quickly evaluate degradation; high-value products should not bear performance risks to save material.

Material Analysis PEEK；recycled material；degradation；heat history；melt index；brittleness

Q

Uneven Conductivity of Carbon Fiber Reinforced PEEK

A

The conductivity of carbon fiber PEEK is directly related to fiber morphology management; orientation anisotropy is an inherent characteristic, and test evaluation must be carried out by zones; gentle shear protects fiber length.

Material Analysis PEEK；carbon fiber；conductivity；orientation；dispersion；shielding

Q

Deformation of PEEK After Annealing

A

PEEK annealing is a double-edged sword — only standardized process can maximize benefits and avoid harm; annealing with fixtured shape-setting balances stress release and shape retention; any annealing specification must pass first-article verification.

Extrusion & Post PEEK；annealing；deformation；stress release；fixturing；dimensions

Q

Melt Fracture Surface Defect of PEEK

A

The core of PEEK melt fracture treatment is local shear rate control; multi-stage injection is the standard means to balance filling and surface quality; gate size is the key design variable.

Molds & Tooling PEEK；melt fracture；sharkskin；shear rate；multi-stage injection；gate

이전 1 ... 802 803 804 805 806 807 808 ... 1164 다음

카테고리

전체 주제 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382