문제 및 해결책

일반적인 플라스틱 재료 문제에 대한 실질적인 답변

기사 둘러보기 →

Q

PA66 fast solidification characteristic

A

PA66 fast solidification determines gate design logic; gate size guarantees feeding, hot runners prevent early freezing, these are two iron rules of mold design; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PA66; fast solidification; gate; 0.5t; submarine gate

Q

PA66 over-drying embrittlement

A

PA66 drying has over-drying risk; 0.1-0.2% is the target range, overtime heat preservation with temperature reduction is the standard handling for production handover; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Material Drying PA66; over-drying; embrittlement; 110℃; thermal oxidation

Q

PA66 mold temperature 80-120℃

A

Mold temperature determines PA66 crystallinity and thus physical properties; 80℃ is the baseline, ±2℃ temperature difference control can reduce shrinkage fluctuation by 40%; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Molds & Tooling PA66; mold temperature; 80℃; crystallinity; ±2℃

Q

PA66 and PA6 temperatures cannot be borrowed from each other

A

PA6 and PA66 are of the same family but different windows; material changeover must change the full set of parameters and fully stabilize, transition-period products are isolated and handled separately; after confirming effectiveness, fix the parameters and practices into the work instruction to ...

Processing Machinery PA66; PA6; material changeover; temperature window; stabilization time

Q

PA66 melt temperature 270-300℃

A

PA66 temperature window is only 20-30℃ above the melting point, the narrowest among the four major nylons; 300℃ is an absolute red line, measured calibration cannot be omitted; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Material Analysis PA66; melt temperature; 270-300℃; narrow window; degradation

Q

PA66 30-minute time limit after drying

A

30 minutes is the exposure time limit for dried PA66; heat-preserving hopper plus sealed feeding, keeping the dried state until the injection moment, counts as completing drying; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Material Drying PA66; moisture regain; 30 minutes; heat-preserving hopper; sealed feeding

Q

PA66 drying equipment selection

A

Equipment selection determines the lower limit of PA66 drying; dehumidifying dryers are a must-have configuration, ordinary hot air drying equals no drying in wet seasons; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Material Drying PA66; dehumidifying dryer; dew point; -30℃; equipment selection

Q

PA66 drying temperature upper limit 90℃

A

PA66 drying temperature upper limit 90℃ is stricter than PA6; what over-temperature brings is not more dryness but oxidative degradation, over-dried material can only be scrapped; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Material Drying PA66; drying temperature; 90℃; oxidative yellowing; over-drying

Q

PA66 drying 0.2% red line

A

0.2% is the PA66 moisture content red line; hydrolysis damage is irreversible, drying, drying, and more drying is the golden rule of PA66 processing; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence

Material Drying PA66; drying; 0.2%; hydrolysis; vacuum drying; 105℃

Q

PA66 high-temperature retention degradation

A

PA66 residence time='minute-level management': high-temperature nylon degrades after staying a few minutes; shutdown SOP is an iron rule for quality assurance and cannot be delayed; after confirming effectiveness, fix the parameters and practices into the work instruction to prevent recurrence.

Processing Machinery PA66; residence time; degradation; shutdown; displacement

이전 1 ... 893 894 895 896 897 898 899 ... 1164 다음

카테고리

전체 주제 11636 Material Drying 1439 Injection Molding 1506 Molding Process 740 Molds & Tooling 1506 Processing Machinery 2025 Extrusion & Post 2239 Blow Molding 315 Thermoforming 141 Material Analysis 1343 Production & Quality 382